background image

M6Mi System Board Manual

2

Copyright Notices

Copyright 

 

1996 Micronics Computers, Inc. The information contained

in the M6Mi PCI/ISA system board manual has been carefully checked
and is believed to be accurate. Micronics assumes no responsibility for any
inaccuracies that may be contained in this document. Micronics makes no
commitments to update or to keep the information in this manual at a
current level when changes are made to the product.

Micronics reserves the right to make improvements to this document
and/or product at any time and without notice. All Rights Reserved. No
part of this document may be photocopied, reproduced, translated, or
reduced to any medium or machine form without prior, written consent
from Micronics.

Portions of the Manual

Portions of this manual were copied (with permission) from Phoenix
Technologies, Ltd. and Micro Computer Systems, Inc. All rights reserved.

Trademarks

IBM is a registered trademark of International Business Machines. Mi-
crosoft and Windows are registered trademarks of Microsoft Corporation.
Intel and PCI are registered trademarks of Intel Corporation. All other
product names mentioned herein are used for identification purposes only
and may be the trademarks of their respective companies.

Содержание M6Mi Pentium Pro

















































































Отзывы: