Micronics M6Mi Pentium Pro Скачать руководство пользователя

Страница: 11 / 80

M6Mi System Board Manual

Section 1: Quick Installation

STATIC!

Before
handling the
M6Mi, be
properly
grounded by
using a
special wrist
or ankle
strap, or
touch a
safely
grounded
object.

Section

Quick Installation

We know that many experienced people prefer to read as
little of the documentation as possible. If this sounds like
you, here’s the short form to get up and running quickly.

Make backup copies of your installation and configu-
ration diskettes.

Ground yourself to prevent damaging static dis-
charge, then remove the M6Mi from its packaging.

Configure and verify the system board’s jumper set-
tings (refer to Jumper Settings in Section 2).

Install the CPU and the system memory (refer to
Section 3).

Install the system board into the chassis and make all
necessary case connections.

Install any ISA and PCI add-on peripherals (refer to
Section 3).

Now you can connect any optional devices (refer to
Section 3).

Turn the computer on and press the <F2> key
when you see the screen in Figure 1.1.

Содержание M6Mi Pentium Pro

















































































Результаты поиска

Содержание M6Mi Pentium Pro

Отзывы:

Похожие инструкции для M6Mi Pentium Pro

Бренды по названию

Популярные бренды

Micronics M6Mi Pentium Pro, Руководство пользователя

Результаты поиска

Содержание M6Mi Pentium Pro

Отзывы:

Похожие инструкции для M6Mi Pentium Pro

Бренды по названию

Популярные бренды