Microhard Systems IP920 Скачать руководство пользователя | Manualshive

Страница: 46 / 73

background image

36

IP920 Operating Manual: Chapter 4 Configuration

4.6.2

Upgrade Password

Upgrade password protects IP920 units from being upgraded (package
upgrade) by unauthorized personel. Default password should be avoided
when system is deployed to make the units more secure.

Figure 16 Change Password for Upgrade

4.6.3

Wireless WEP Encryption

Network traffic over air can be encrypted by

Wired

Equivalent

Privacy

(WEP)

encryption algorithm.

WEP encryption is disabled by default to keep overhead minimum, it
should be enabled if over air encryption is required. When enabled, more
protocol overhead is added on the packets being transmitted; therefore a
minor throughput decrease shall be expected.

«
...
44
45
46
47
48
...
»

Содержание IP920










































































Отзывы:

Нет отзывов

Похожие инструкции для IP920

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Бренд: Pakedge Device & Software Страницы: 20

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Бренд: Hawking Страницы: 2

Бренд: Idis Страницы: 31

Бренд: Patton electronics Страницы: 65

Бренд: Net to Net Technologies Страницы: 4

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Бренд: Keithley Страницы: 98

Бренд: Hawking Страницы: 21

TGXPS-1080-M12-MV Series

Бренд: ORiNG Страницы: 2

Бренд: Valcom Страницы: 4

Бренд: Planet Страницы: 66

Бренд: AIC Страницы: 79

RouteFinder RF560VPN

Бренд: Multitech Страницы: 82

Safeguard for Privileged Sessions 3000

Бренд: One Identity Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды