micro-trak ProPlant, Справочное руководство, Страница: 30 / 48

30
Press to
enter or exit
calibration
mode.
Press to
increase or
decrease
values.
Red warning light will be lit when
in CAL.
ROWS
SECTION
METER
CAL
ROW
SPACING
ADJUST
RATE
TARGET
RATE
SPEED
CAL
METER CAL
TEST
TEST
SPEED
RPM
(1) (2) (3)
DISTANCE
AREA /
HOUR
SEEDS
(1) (2) (3)
SEEDS /
DISTANCE
SPEED
AREA
(1) (2) (3)
ON
OFF
L C R
SECTIONS
RUN
HOLD
CAL
AUTO
MAN
RESET
ON / OFF
____
SEED RATE
SEED
SPACING
RATE 1
RATE 2
RATE 3
V 1 2 3 4 5
CAL HOLD
ROWS
SECTION
METER
CAL
ROW
SPACING
ADJUST
RATE
TARGET
RATE
SPEED
CAL
METER CAL
TEST
TEST
SPEED
RPM
(1) (2) (3)
DISTANCE
AREA /
HOUR
SEEDS
(1) (2) (3)
SEEDS /
DISTANCE
SPEED
AREA
(1) (2) (3)
ON
OFF
L C R
SECTIONS
RUN
HOLD
CAL
AUTO
MAN
RESET
ON / OFF
____
SEED RATE
SEED
SPACING
RATE 1
RATE 2
RATE 3
V 1 2 3 4 5
CAL HOLD
Illustration 5
English or Metric?
The ProPlant is capable of displaying in for ma tion in
Amer i can En glish or standard Metric measurement. The
ProPlant is shipped from the factory programmed for
English.
NOTE: The following procedures will also load factory
default calibration values. To simply change units
without loading defaults, see the “Special” Calibration
section.
METRIC
• You must be in HOLD or have all sections OFF to enter
Cal. To activate the Metric mode, turn power OFF and
place the ro ta ry switch at “AREA.” Hold down both
the “CAL” and “-” keys and turn power ON. See Il lus tra-
tion 11. The con sole will display LOAd. Once LOAd is
displayed, release the two keys. To “lock-in” Metric mode
you must enter and exit cal i bra tion. Press and hold the
CAL key until “CAL” icon appears on the display. The con-
sole is now in cal i bra tion and Metric mode is selected.
Exit CAL by pressing and holding the “CAL” key until CAL
disappears from the display (ap prox i mate ly 1 second).
NOTE: You must exit CAL to lock in Metric units.
Calibration
Loading Default Calibration Values
Illustration 6
Entering Calibration Values
To enter or change any of the system’s calibration values,
you must enter calibration mode. To enter calibration mode,
STOP the vehicle, turn all sections OFF or put the console in
HOLD and press and hold the CAL button until the “CAL” icon
appears (approximately one second).
(NOTE: Calibration
may be entered while moving, but it is not rec om mend ed to
attempt calibration while the vehicle is mov ing.)
The console
will remain in calibration mode, with the RED warning light
illuminated until you exit calibration or turn power OFF.
Once in calibration mode, you may change any one, all, or
none of the values, in any order.* To select a calibration
position, simply turn the rotary selector to the desired
po si tion. Calibration positions are identified by the WHITE
labeling on each side of the rotary selector. All values are
entered and adjusted using the “+” and “-” but tons on the
front panel.
*Test speed must be last.
Hold the “CAL” key again for 1 second to exit calibration.
“CAL” will disappear from the display.
NOTE: You must exit
CAL to save changes.
ENGLISH
• You must be in HOLD or have all sections OFF to enter
Cal. To activate the English mode, turn power OFF
and place the ro ta ry switch in the SEEDS position. Hold
down both the “CAL” and “-” keys and turn power ON.
The con sole will display LOAd. Once LOAd is displayed,
release the two keys. To “lock-in” English mode you
must enter and exit cal i bra tion. Press and hold the CAL
key until “CAL” lights on the display. The console is now
in cal i bra tion and English mode is selected. Exit CAL by
pressing and holding the “CAL” key until CAL disappears
from the display (approximately 1 second). NOTE: You
must exit CAL to lock in English units.
NOTE: In metric, the SPEED CAL will display 2 decimal
places, in English it will display 3 places. Also, changing
from En glish to Met ric mode may change or alter any
previously en tered cal i bra tion values. After switch ing
mea sure ment modes, con firm that all cal i bra tion val-
ues are correct.