MICRO-AIR EasyTouch 355 Скачать руководство пользователя страница 3

Страница: 3 / 15

July 1, 2021, revision 1.8

The EasyTouch 355 model thermostats were

designed to directly replace Coleman™, Airxcel™

and RVP™

ZC thermostats. Original thermostats must have model numbers of 9330-333, 9330-334,

9330-335, 9330-336, or 9430-334 to be replaced by this thermostat. If your thermostat is not listed,
please contact Micro-Air

https://www.micro-air.com/SupportRequest

to verify the thermostat you

received is correct for your application.

Installing the thermostat

There are three steps to installing the thermostat. First remove your old thermostat. Next

disconnect and reconnect the wiring. Finally install the mounting pins to the wall and mount your new
thermostat.

Removing the old thermostat

The original thermostat is held to the wall with a backing plate that

extends about ¼” (6.3mm)

from the wall. The thermostat can be “popped off” the plate to access the mounting screws behind it.

Remove the screws and unplug the two connections on the cable harness. Note, some thermostats are
directly wired by the manufacturer. See the next section for further details.

Содержание EasyTouch 355
















Результаты поиска

Содержание EasyTouch 355

Отзывы:

Похожие инструкции для EasyTouch 355

Бренды по названию

Популярные бренды

MICRO-AIR EasyTouch 355, Руководство по эксплуатации

Результаты поиска

Содержание EasyTouch 355

Отзывы:

Похожие инструкции для EasyTouch 355

Бренды по названию

Популярные бренды