Michell Instruments Optidew Скачать руководство пользователя страница 6

Страница: 6 / 66

Optidew Series User’s Manual

97430 Issue 2, March 2017

Safety

The manufacturer has designed this equipment to be safe when operated using the procedures

detailed in this manual. The user must not use this equipment for any other purpose than that

stated. Do not apply values greater than the maximum value stated.

This manual contains operating and safety instructions, which must be followed to ensure the safe

operation and to maintain the equipment in a safe condition. The safety instructions are either

warnings or cautions issued to protect the user and the equipment from injury or damage. Use

quali

ed personnel and good engineering practice for all procedures in this manual.

Electrical Safety

The instrument is designed to be completely safe when used with options and accessories supplied

by the manufacturer for use with the instrument.

Pressure Safety

DO NOT permit pressures greater than the safe working pressure to be applied to the instrument.

The speci

ed safe working pressure is 20 barg (300 psig). The pressure rated versions can withstand

250 barg (3600 psig).

Toxic Materials

The use of hazardous materials in the construction of this instrument has been minimized. During

normal operation it is not possible for the user to come into contact with any hazardous substance

which might be employed in the construction of the instrument. Care should, however, be exercised

during maintenance and the disposal of certain parts.

Repair and Maintenance

The instrument must be maintained either by the manufacturer or an accredited service agent. Refer

to www.michell.com for details of Michell Instruments’ worldwide of

ces contact information.

Calibration

The recommended calibration interval for the Optidew Series is one year, unless otherwise speci

by Michell Instruments. The instrument should be returned to the manufacturer, Michell Instruments,

or one of their accredited service agents for re-calibration. Refer to www.michell.com for details of

Michell Instruments’ worldwide of

ces contact information.

Safety Conformity

This product meets the essential protection requirements of the relevant EU directives.

Содержание Optidew



































































Результаты поиска

Содержание Optidew

Отзывы:

Бренды по названию

Популярные бренды

Michell Instruments Optidew, Руководство пользователя

Результаты поиска

Содержание Optidew

Отзывы:

Бренды по названию

Популярные бренды