background image

Mi-T-M

 Pit Cleaner Operator's Manual    

 

 

 

 

 

 

 

                 7

RISK OF BODILY INJURY

Injury may occur from the unit.

!SAVE THESE INSTRUCTIONS!

POTENTIAL CONSEQUENCE

PREVENTION

IMPORTANT SAFETY WARNINGS

READ ALL SAFETY WARNINGS BEFORE USING PIT CLEANING SYSTEM

DO NOT DRINK THE WATER IN THE UNIT!!  

This is non-potable water and is not suitable 

for consumption.
DO NOT allow children to operate this unit.
DO NOT overreach or stand on unstable 

support.  
Wet surfaces can be slippery, wear protective 

foot gear and keep good footing and balance 

at all times.  
Know how to stop the unit.  Be thoroughly 

familiar with controls.
Before servicing, ALWAYS shut off the pressure 

washer.
Consult Material Safety Data Sheets for safe 

handling of chemicals used with your system, 

especially oxidizers and acids.
SEEK EMERGENCY MEDICAL CARE if the 

spray appears to have penetrated the skin!   

DO NOT TREAT AS A SIMPLE CUT!!  Be 

prepared to tell a physician exactly what kind 

of chemicals you were using by reading the 

Material Safety Data Sheet  (MSDS) provided 

with your chemical. 
Never use any solvents, detergents or acid type 

cleaners with this unit.
Protective equipment such as gloves and rubber 

boots are advisable, especially when using 

cleaning detergents.
ALWAYS wear protective goggles when 

operating the unit to shield the eyes from flying 

debris. 
DO NOT direct spray toward fragile materials 

such as glass for shattering could occur.
Stay alert-watch what you are doing.  Do not 

operate the unit when fatigued or under the 

influence of alcohol or drugs.
NEVER squeeze the trigger unless securely 

braced.    
NEVER trigger the gun while on a ladder or 

roof.
DO NOT leave pressurized unit unattended.  

Shut off the pressure washer and release 

trapped pressure before leaving.
  

Serious injury can occur from loose 

debris being propelled at a high speed 

from the spray gun.

Injury may occur if the operator loses 

his balance caused by the thrust of 

water traveling through the spray 

nozzle.

HAZARD

Содержание RC-0002-0001

















Отзывы: