MHSC SB44SS Скачать руководство пользователя страница 21

SB44SS Outdoor Woodburning Fireplace

87D0059

1

ChIMNey Cap INSTaLLaTION

ChIMNey Cap

SpeCIaL NOTe:

 

The proper height as previously explained is important to assure proper draft 

and safety. The chimney cap extends the flue outlet four inches above the top of the last section 
of chimney. This should be kept in mind when determining the proper height for the chimney.  
The chimney should not be extended more than 90 inches above the supporting roof structure 
without additional support. In the case of an “A” frame type construction or other steep pitch 
roofs that require more than 90 inches of chimney above the roof, a support should be attached 
to the chimney at the 90 inch level that is strong enough to support a wind load of 3

Z\,

 pounds 

for each inch the chimney extends above 90 inches. The flue outlet must be a minimum of three 
feet above the point where in penetrates the roof.

CauTION:

    Be  careful  to  avoid  electrical  shock  hazard  when  contacting  wires  to  the  metal 

chimney components.
1.  Extend the regular chimney sections until the top of the chimney is 4 inches below the total 

flue height desired. Do not snap the last section of inlet air duct or largest diameter pipe in 
place until Step 3 is completed.

.  Remove the shingles from around the chimney so that the flashing may be installed, with the 

upper part of the flashing under the shingles.

3.  Set the flashing on the roof. Hold a section of the outside pipe (13” diameter) on the flashing 

and scribe a line around the flashing, then cut the top off the flashing by cutting 1/4 inch below 
the scribed line. This should increase the diameter of the flashing outlet sufficiently to allow 
the flashing to be placed over the chimney.  

Figure 26

4.  Snap the last section of inlet air duct in place and slide the flashing over the chimney. Adjust 

the chimney to assure that the proper minimum clearances are maintained.

5.  Nail the flashing securely in place with eight nails.
6.  Seal the crack between the top of the flashing and the chimney with mastic. Leave some 

excess mastic at this area to be used in step eight. 

NOTe:

  Use pliers and wear gloves when 

performing step seven to minimize the danger of cutting your hands on the edge of the storm 
collar.

7.  Place the storm collar around the chimney and put the collar together like a belt in belt loops.  

Slide the end of collar under the two loops on the other end with the loops facing up. Overlap 
the ends of the collar until it is tight against the chimney. Bend the free end of the collar back 
over the loops to hold the storm collar securely together. The excess end of the storm collar 
may be trimmed off.

8.  Slide the storm collar down snugly against the flashing until the excess mastic left in step 

six is forced up into the crack between the storm collar and the chimney.  This should make 
the joint between the flashing and the chimney watertight.

9.  Install the chimney cap by placing the cap into matching parts of the last chimney section.  

Then punch or drill 1/8 inch diameter holes in the inlet air duct (chimney pipe) where specified 
on the brackets and fasten it down with the No. 8 screws provided. Do not penetrate the inner 
stainless steel pipe while installing the screws.

10.Check all the parts of the fireplace, chimney and chimney termination cap to assure that no 

parts have been damaged or bent during installation and that all parts have been installed 
properly.

NOTe:

 

 The metal used for the chimney cap has a rust protective coating but the cut edges of 

the parts are not protected. To prevent rusting and rust staining of nearby structures, exposed 
parts of the chimney and chimney cap should be detergent washed and painted with a galvanized 
primer paint.

Содержание SB44SS





































Отзывы: