MFJ MFJ-926B Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 20

MFJ MFJ-926B Скачать руководство пользователя страница 18

MFJ-926B HF Automatic Remote Antenna Tuner

Instruction Manual



2010 MFJ Enterprises, Inc.

15

7. Turn on the power to the transmitter. Set and lock the frequency to

exactly

29.000 MHz.

8. Press and hold

only

the [ANT] button while turning the power on. Both LEDs will blink until the

button is released.

9. Within four seconds of releasing [ANT], press the [TUNE] button six times.
10. After releasing [TUNE] for four seconds, the green LED lights up and the Frequency Counter

Calibration is initiated.

11. Key the transmitter to output about 10 watts and adjust trimmer capacitor VC3 (located next to

the big integrated circuit on the front side of the front panel circuit board) until both LEDs are
lighted up. The green LED lights when the calibration is below 29 MHz, the red LED lights
when the calibration is above 29 MHz and both LEDs light up when the calibration equals to 29
MHz.

12. Unkey the transmitter. Turn off the power to the transmitter and the tuner.
13. Secure the cover back onto the tuner.

SWR Bridge Calibration

This is a factory calibration procedure only

In Case of Difficulty

If the tuner acts erratic, reset the tuner to factory defaults.

If the tuner fails to tune, please

double check

all connections and follow the tuning procedures again.

If the tuner arcs

at the rated power levels, please

double check

all connections and follow the tuning

procedures again. Ensure you are not exceeding the tuner’s rated power handling capability.

Note:

If the tuner arcs when operating on the 160-meter band, it may be necessary to reduce
transmitter output power.

If you are still unsuccessful, but the tuner does adjust and operate when used with a dummy load or
another antenna, please read “Grounding Hints” and “Antenna System Hints” on page 13.

Technical Assistance

If you have any problem with this unit first check the appropriate section of this manual. If the manual
does not reference your problem or your problem is not solved by reading the manual, you may call

MFJ

Technical Service

at 662-323-0549 or the

MFJ Factory

at 662-323-5869. You will be best helped if you

have  your unit, manual and all information on your station handy so you can answer any questions the
technicians may ask.

You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road, Starkville, MS
39759;  by  facsimile  (FAX)  to  662-323-6551;  or  by  email  to  [email protected].    Send  a
complete  description  of  your  problem,  an  explanation  of  exactly  how  you  are  using  your  unit,  and  a
complete description of your station.  Also include the firmware version number of your unit.

«
...
16
17
18
19
20
»

Содержание MFJ-926B





















Отзывы:

Нет отзывов