manualshive.com logo in svg

MFJ MFJ-926B, Инструкция по эксплуатации, Страница: 14 / 20

Поделиться
Скачать
MFJ MFJ-926B Скачать руководство пользователя страница 14

MFJ-926B HF Automatic Remote Antenna Tuner 

Instruction Manual 

 2010 MFJ Enterprises, Inc. 

11

 

Appendices 

 

POWER-ON OPERATIONS

(Press and hold buttons while turning on the power.)

Press and hold                                      +                     to start the self test.

POWER

TUNE

POWER

Press and hold                  +                     then press                 1 time to reset factory defaults.

ANT

TUNE

POWER

Press and hold                  +                     then press                 2 times to delete current memory bank.

ANT

TUNE

POWER

Press and hold                  +                     then press                 3 times to perform total reset.

ANT

TUNE

POWER

Press and hold                  +                     then press                 4 times to test the power-down circuitry.

ANT

TUNE

POWER

Press and hold                  +                     then press                 5 times to test the relays.

ANT

TUNE

POWER

Press and hold                  +                     then press                 6 times to calibrate the frequency counter.

ANT

TUNE

Press and hold                  +                     then press                 7 times to calibrate the SWR bridge.

POWER

ANT

TUNE

Press and hold                  +                  +                     to delete current antenna memory.

POWER

ANT

TUNE

For the                  +                     operations, not pressing                 or pressing it more than seven times

will cancel the operation after idling four seconds, beep two times and then resume normal operation.

POWER

ANT

TUNE

 

 

Figure 2.  Power-On Operations. 

 
 

Resetting the Tuner 

 
Each  time  the  tuner  is  powered  off,  the  microprocessor  saves  all  memories  and  configurations  to  non-
volatile memory.  If the tuner is not working properly, even on initial power on, try resetting to the factory 
defaults. 
 

Factory Defaults 

 
The unit is shipped with the following default settings: 

• 

Inductance 

0 

µ

H 

• 

Capacitance 

0 pF on antenna side 

• 

Memory 

Bank 1A 

 

• 

Tuning Mode 

Automatic 

• 

Sticky-Tune 

Off 

 

 

 
 

Note: 

Resetting to factory defaults does not erase the antenna memories. 

 
 
 
 

Содержание MFJ-926B





















Отзывы:

Нет отзывов