background image

MFJ-8621                                                                                             Data Radio 

14 

FULL 12 MONTH WARRANTY 

 

MFJ Enterprises, Inc. warrants to the original owner of this product, if manufactured by MFJ 
Enterprises, Inc. and purchased from an authorized dealer or directly from MFJ Enterprises, Inc. 
to be free from defects in material and workmanship for a period of 12 months from date of 
purchase provided the following terms of this warranty are satisfied. 

 

1.

 

The purchaser must retain the dated proof-of-purchase (bill of sale, canceled check, credit 
card or money order receipt, etc.) describing the product to establish the validity of the 
warranty claim and submit the original of machine reproduction or such proof of purchase 
to MFJ Enterprises, Inc. at the time of warranty service.  MFJ Enterprises, Inc. shall have 
the discretion to deny warranty without dated proof-of-purchase.  Any evidence of 
alteration, erasure, or forgery shall be cause to void any and all warranty terms 
immediately. 

 

2.

 

MFJ Enterprises, Inc. agrees to repair or replace at MFJ's option without charge to the 
original owner any defective product under warrantee provided the product is returned 
postage prepaid to MFJ Enterprises, Inc. with a personal check, cashiers check, or money 
order for 

$7.00 

covering postage and handling. 

 

3.

 

MFJ Enterprises, Inc. will supply replacement parts free of charge for any MFJ product 
under warranty upon request.  A dated proof of purchase and a

 $5.00

 personal check, 

cashiers check, or money order must be provided to cover postage and handling. 

 

4.

 

This warranty is 

NOT

 void for owners who attempt to repair defective units.  Technical 

consultation is available by calling (601) 323-5869. 

 

5.

 

This warranty does not apply to kits sold by or manufactured by MFJ Enterprises, Inc. 

 

6.

 

Wired and tested PC board products are covered by this warranty provided 

only the 

wired and tested PC board product is returned.

  Wired and tested PC boards installed 

in the owner's cabinet or connected to switches, jacks, or cables, etc. sent to MFJ 
Enterprises, Inc. will be returned at the owner's expense unrepaired. 

 

7.

  

Under no circumstances is MFJ Enterprises, Inc. liable for consequential damages to 
person or property by the use of any MFJ products. 

 

8.

 

Out-of-Warranty Service: 

MFJ Enterprises, Inc. will repair any out-of-warranty product 

provided the unit is shipped prepaid.  All repaired units will be shipped COD to the 
owner.  Repair charges will be added to the COD fee unless other arrangements are made. 

 

9.

 

This warranty is given in lieu of any other warranty expressed or implied. 

 

10.

 

MFJ Enterprises, Inc. reserves the right to make changes or improvements in design or 
manufacture without incurring any obligation to install such changes upon any of the 
products previously manufactured. 

 

11.

 

All MFJ products to be serviced in-warranty or out-of-warranty should be addressed to 

MFJ Enterprises, Inc., 300 Industrial Park Road, Starkville, Mississippi 39759, USA 

and must be accompanied by a letter describing the problem in detail along with a copy of 
your dated proof-of-purchase. 

 

12.

 

This warranty gives you specific rights, and you may also have other rights which vary 
from state to state. 

Содержание MFJ-8621
















Отзывы: