background image

MFJ-991 / MFJ-994 IntelliTuner Automatic Antenna Tuners 

Instruction Manual 

 

©

 2004 MFJ Enterprises, Inc.

 

2

Features 

 

• 

Automatically matches antennas from 6 to 3200 ohms impedance (MFJ-991); 12 to 800 ohms (MFJ-
994) 

• 

Handles 150 watts PEP SSB/100 watts CW (MFJ-991); 600 watts PEP SSB/300 watts CW (MFJ-
994) 

• 

Tune in less than 15 seconds, usually less than 5 seconds 

• 

Over 1000 non-volatile memories for tuner settings 

• 

Highly efficient switching L-network matching circuit 

• 

1.8 to 30 MHz continuous frequency coverage 

• 

Selectable target SWR 1.5 or 2.0 

• 

Selectable SWR threshold 0.5, 1.0 or 1.5 

• 

Lighted cross-needle SWR/wattmeter with high, low and auto range options 

• 

Built-in frequency counter 

• 

SO-239 coax fed antenna connector 

• 

Connector for random wire or single wire antennas 

• 

Optional remote control 

• 

Optional radio interface for compatible radios 

 
 

Specifications 

 

• 

Impedance matching range:  6 to 3200 ohms (MFJ-991); 12 to 800 ohms (MFJ 994) 

• 

Minimum power for tuning:  5 watts (MFJ-991); 10 watts (MFJ-994) 

• 

Maximum power while tuning:  100 watts with foldback, 20 watts without foldback 

• 

RF power limit:  150 watts PEP SSB/100 watts CW (MFJ-991); 600 watts PEP SSB/300 watts CW 
(MFJ-994) 

• 

Frequency range:  1.8 to 30 MHz continuous coverage 

• 

Frequency counter accuracy:  ±1 kHz across HF bands 

• 

Frequency counter range:  up to 50 MHz 

• 

Capacitance range:  0 to 3900 pF (MFJ 991, 256 values); 0 to 2950 pF (MFJ-994, 192 values) 

• 

Inductance range:  0 to 24 µH (MFJ-991, 256 values); 0 to 17 µH (MFJ-994, 192 values) 

• 

Relay rating:  16 amp 1000 volts 

• 

Relay electrical life:  100,000 operations 

• 

Relay mechanical life:  10 million operations 

• 

Memory endurance:  1 million write cycles 

• 

Memory data retention:  100 years 

• 

Power requirements:  12 - 15 volts DC, 2.1 × 5.5 mm coaxial plug, center pin positive 

• 

Current consumption:  1 amp or less 

• 

Dimensions (approx.):  10.1 × 2.8 × 9.2 in. (257 × 71 × 234 mm) (width/height/depth) 

 

not including connectors 

• 

Weight (approx.):  3.7 lb (1.68 kg) 

 
 
 
 
 

†  Specifications and design are subject to change without notice. 

Содержание IntelliTuner -991





























Отзывы: