MFJ IntelliTuner -991 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 28

background image

MFJ-991 / MFJ-994 IntelliTuner Automatic Antenna Tuners

Instruction Manual

©

2004 MFJ Enterprises, Inc.

21

Technical Assistance

If you have any problem with this unit first check the appropriate section of this manual. If the manual
does not reference your problem or your problem is not solved by reading the manual, you may call

MFJ

Technical Service

at 662-323-0549 or the

MFJ Factory

at 662-323-5869. You will be best helped if you

have your unit, manual and all information on your station handy so you can answer any questions the
technicians may ask.

You can also send questions by mail to MFJ Enterprises, Inc., 300 Industrial Park Road, Starkville, MS
39759; by facsimile (FAX) to 662-323-6551; or by email to [email protected]. Send a
complete description of your problem, an explanation of exactly how you are using your unit, and a
complete description of your station.

List of Accessories

•

MFJ-993RC

: Remote control

•

MFJ-1316

: 12 VDC 1.5 amp power supply

•

MFJ-5124A

: Interface cable for compatible Alinco radios

•

MFJ-5124I

: Interface cable for compatible Icom radios

•

MFJ-5409

: 6 feet long RS-232 cable, female DB-9 to male DB9 connector

•

MFJ-5803

: 3 feet long RG-58 A/U 50-ohm coax cable with a PL-259 connector on each end

•

MFJ-5806

: 6 feet long RG-58 A/U 50-ohm coax cable with a PL-259 connector on each end

•

MFJ-5818

: 18 feet long RG-58 A/U 50-ohm coax cable with a PL-259 connector on each end

«
...
23
24
25
26
27
...
»

Содержание IntelliTuner -991





























Отзывы:

Нет отзывов

Похожие инструкции для IntelliTuner -991

Бренд: Datron Страницы: 16

Бренд: Hama Страницы: 8

Бренд: NARDA Страницы: 142

Бренд: MFJ Страницы: 5

Бренд: Ellies Страницы: 2

Бренд: EchoStar Страницы: 28

Бренд: Televes Страницы: 2

Бренд: Winegard Страницы: 19

GEOSATpro GS120 DiSEqC

Бренд: Satellite AV Страницы: 10

Бренд: Teltonika Страницы: 40

Бренд: OPTIBEAM Страницы: 12

Бренд: I0JXX Страницы: 4

Бренд: Univers by FTE Страницы: 64

Бренд: Taoglas Страницы: 4

NBE-M2-400 NanoBeam M

Бренд: Ubiquiti Страницы: 24

Бренд: MFJ Страницы: 4

Legal Limit IntelliTuner MFJ-998RT

Бренд: MFJ Страницы: 28

Бренд: Icom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды