background image

MFJ-991 / MFJ-994 IntelliTuner Automatic Antenna Tuners 

Instruction Manual 

©

 2004 MFJ Enterprises, Inc. 

 

11

Component Limit 

 
The upper limits of inductance (L) and capacitance (C) are factory-limited according to frequency and 
maximum power rating; i.e., higher frequencies need less inductance and less capacitance when the L-
network is properly tuned.  Pressing [C-UP] and/or [L-UP] allows capacitance and inductance to be 
increased only to these limits.  When a selected capacitance or inductance is higher than its allowed limit, 
and the frequency is changed, that selection is automatically reduced to the value of its limit.  These limits 
are used to prevent matching of extreme load impedance outside the tuner’s specification, which may 
result in excess voltage and/or current across the tuner’s components. 
 
 

Antenna Memory 

 
The “memory resolution” is the width of frequency spectrum that the tuner recognizes as being the same 
as a tuned frequency already in memory.  The memory resolution is approximately 0.1 percent of the 
lower frequency of each amateur band.  For example, the memory resolution on the 40-meter band (7000 
to 7300 kHz) is 7 kHz; if the tuner has memorized a setting for 7050 kHz, it will automatically call up this 
setting for any frequency from 7047 to 7053 kHz.  The memory resolutons for the HF amateur bands 160 
through 10 meters are: 
 

Meter 

Frequency Range (kHz) 

Memory Resolution (kHz) 

160 

1800 – 2000 

75/80 

3500 – 4000 

60 

5330.5, 5346.5, 5366.5; 5371.5 and 5403.5 

two memory locations 

40 

7000 – 7300 

30 

10100 – 10150 

10 

20 

14000 – 14350 

14 

17 

18068 – 18168 

18 

15 

21000 – 21450 

21 

12 

24890 – 24990 

25 

10 

28000 – 29700 

28 

 

Table 1.  Antenna Memory Resolution. 

 
The memory resolution for non-amateur frequency bands between 160 and 10 meters is approximately 
one percent of the lower frequency of that band.  There are more than one thousand antenna memory 
locations. 
 
To clear the antenna memory, turn off the power to the tuner, then press and hold both [TUNE] and [C-
DN] buttons while turning on the power.  Both meter needles will read half scale, forming a triangle, 
asking you to confirm the deletion.  Press [C-UP] to confirm delete (both meter needles will read full 
scale), or press [L-UP] to cancel the antenna memory delete (both meter needles will read zero). 
 
“Total Reset” erases the antenna memory 

and

 returns all tuner settings to their factory default states.  To 

achieve this, turn power off, press and hold [TUNE], [L-DN] and [C-DN] buttons while turning on the 
power.  The meter needle readings will be the same as for antenna memory delete:  half scale.  Press [C-
UP] to confirm total reset (needles go to full scale) or press [L-UP] to cancel total reset (needles go to 
zero). 
 
 

Содержание IntelliTuner -991





























Отзывы: