manualshive.com logo in svg

Meyer E-58H, Руководство по обслуживанию

Поделиться
Скачать
Meyer E-58H Скачать руководство пользователя страница 75

-73-

ELECTRONIC TROUBLESHOOTING E-78 & E-88

TIMEOUTS:

  The  RCM  will  power  off  after  2  hours 

of inactivity. This conserves battery life if the unit is 
accidentally left on when driver leaves. This should 
provide ample time to transport between jobs or just 
to stop for lunch, etc. Simply pressing any button can 
reset this timer.

The Plow lights will remain powered on if there is a 
loss  of  communications.  The  moldboard  functions 
will be disabled during this time. This can occur for a 
couple of different reasons: 

1.  If  the  Meyer  accessory  port  plug  is  accidentally 
pulled out before the RCM is powered off normally.

2. If there is a real loss of communication between the 
PCM, HCM and RCM.

Overcurrent:

 The hydraulic unit will be shut down if an 

overcurrent situation occurs for more than 2 seconds. 
An  alarm  will  sound  and  “Overcurrent”  will  appear 
on the display. This might happen when the blade is 
taken to full stops in any direction and held. “Stacking 
snow” is one reason this may occur. To reset, simply 
release the button and press again. If the fault occurs 
again the hydraulic unit will be shut down again.
                        

Alarms/Faults:

  All  faults  will  sound  an  alarm.  To 

extinguish  the  alarm,  press  any  button.  To  remove 
fault from the screen, press the 

Exit

 button to return to 

normal screen. The fault will remain in the diagnostic 
menu until it is cleared. All moldboard functions will 
remain active during the alarms, unless perhaps it is 
a bad solenoid. Example: A bad “B” solenoid, then 
the moldboard cannot be moved Up, but Left, Right, 
and Down are still available.

4. TROUBLESHOOTING DIAGRAMS

RCM will not power On

Plow Lights do not follow OEM switch positions 
(RCM and PCM are connected correctly and are 
working)

RCM Display shows Dark Lines, Updates slowly

4.0 Troubleshooting Flow Diagrams 

Press

Green

button > 1

sec ?

Press green button

for 1 second

No

RCM will emit the

triple beep at

power on even if

the button click is

turned off through

the menu

Power

getting to

RCM ?

Check all electrical

connections

Power cycle RCM

No

Yes

RCM will not power ON

Replace RCM

Yes

Is HCM

connected

securely

and

correctly?

Are voltage

levels

correct?
(refer to

manual)

Does HCM

icon

appear on

RCM

display?

Replace HCM

Yes

Yes

Yes

Clean and tighten

connections

No

Power cycle HCM

No

If after power

cycle, still no icon.

Replace HCM

Plow Lights do not follow OEM switch postions

(RCM and PCM ARE connected correctly and are working)

RCM Display shows Dark Lines, Updates slowly

BLade,

Lights

working

normally ?

LCD display is

cold. This should

cause no

functional problems

An LCD display will

not update/refresh

itself very quickly in

cold weather. All

blade functions

should be normal.

The information on

the screen may be

slow to keep up

with the action

though.

Allow the RCM to

warm up.

Yes

Power to RCM was

disconnected

abnormally. Power

cycle the RCM,

verify secure

connections to

RCM and cigar

accessory jack.

No

Содержание E-58H















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды