manualshive.com logo in svg

Meyer E-58H, Руководство по обслуживанию

Поделиться
Скачать
Meyer E-58H Скачать руководство пользователя страница 22

DIAGNOSTIC FLOW CHART FOR

E-88 Unit

These charts are intended to be used as an aid in diagnosing problems on the E-88 unit.  They are not a substitute for factory training 
and experience.  Be certain to read the General Information and Testing Tips sections before attempting any troubleshooting. 

IMPORTANT: Maintenance and repairs must be performed with the moldboard on the ground.

General Information

 

 

Before any troubleshooting is started, make certain the following conditions are met.

 

1.  The moldboard is pointing straight ahead.  This can often be done by coupling the left cylinder into the right cylinder and 

pushing the moldboard by hand.

 

2.  The power angling cylinders must be installed correctly on to the plow assembly.  The left cylinder (Driver’s side) has a hose 

attached with a female half of a coupler at the end; the right cylinder (Passenger side) has a hose attached with a male half 
of a coupler at the end.

 

3.  The solenoid wires must be on their proper coil. The “A” coil (black and tan wires) on power angling block labeled “BLK”. 

The “B” coil (red and tan wires) on power angling block labeled “RED”.  The “C” coil (green and tan wires) on power angling 
block labeled “GRN”. The “D” coil (yellow and tane wires) on power angling block labeled “YEL”. The “E” coil (purple and tan 
wires) on power angling block labeled “PUR”.

 

TESTING TIPS

 

-20-

 

 

Many  tests  do  not  require  removing  the  Electro  Lift

®

  unit  from  the  vehicle.    However,  more  thorough  testing  can  be  

performed using the Meyer Test Stand which allows direct pressure and amperage readings.

 
 

1.  Using a screwdriver or other small tool to check for magnetism of the solenoid coils “A”, “B”, “C”, “D” and “E”.  Place the tool 

on the nut securing the coil and have an assistant operate the switch.  You should feel strong magnetic attraction.

 

2.  Use a test light or volt meter to determine whether there is power at the harness. 

 

3.  When determining AMP draw of the motor, always obtain the highest value possible, i.e, at maximum raise or maximum angle 

with motor running.

 

4.  Proper rotation for the motor is indicated by an arrow located on top side of the (Part # 15889) pump.

 

5.  The pump shaft of a good pump can be turned smoothly using two fingers.  If it can’t be turn easily, the pump is too tight and 

must be replaced.

 

6.  Pump pressure can be measured at an angle hose (note pressure at full angle) or in the pressure filter port (an adaptor is 

necessary for the filter port). Note: The E-88 Unit has a non adjustable pressure relief valve. 

 

7.  Flush the complete system including unit, hoses and power angling rams with Meyer Hydra-Flush™ Fluid M-2.

Содержание E-58H















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды