Meyer E-58H Скачать руководство пользователя страница 20

Страница: 20 / 78

SOLENOID SWITCH

The E-58H, E-78 & E-88 motor requires more current

or amperage to operate than the vehicle wiring, vehicle

ignition switch or toggle switches have the capacity to

handle. The solenoid switch is essentially a heavy duty

switch with the capacity to handle the heavy current

required by the motor. It is closed electrically by the

solenoid to convey the heavy current directly from the

vehicle battery via heavy gauge electrical cable. The

solenoid, which functions essentially the same as the

previously described solenoid valves, receives its low

amperage current at the proper times via the wiring

harness. This solenoid must be grounded to operate

properly.

FILTERS

Cleanliness is perhaps the single most important

ingredient in assuring a hydraulic system’s reliability.

Should the hydraulic ﬂuid become contaminated,

malfunction and permanent damage to the hydraulic

system may occur. For this reason, all the E-58H,

E-78 & E-88 units are equipped with a ﬁlter system

consisting of:

• A ﬁne screen strainer on the reservoir pump inlet.

•A high pressure ﬁlter on the pressure side of the

pump.

•A return ﬁlter on the power angling block leading

back to the reservoir..

With this system, the hydraulic ﬂuid is ﬁltered as it

leaves the reservoir on its way to the pump and on

the Power Angling units ﬁltered again as it leaves the

pump. Because clean hydraulic ﬂuid is most important

to insure Solenoid Valve reliability, the hydraulic ﬂuid

leaving all cylinders is ﬁltered before passing returning

to the reservoir. The ﬁlter screen, high pressure and

return ﬁlter are easily removed for periodic cleaning

or replacement.

IMPORTANT:

Should the hydraulic ﬂuid become contaminated, it

will be necessary to replace all the hydraulic oil in the

system. The complete system (hydraulic unit, power

angling cylinders, mount cylinder and hoses) should

be ﬂushed. Flush the system with Meyer Hydra-Flush™

Fluid M-2.

ELECTRO LIFT® UNIT COMPONENTS CONT.

CHECK VALVES

Check valves are very simple devices that have two

basic functions: They prevent fluid from passing

through them in one direction, but they allow ﬂuid to

pass through them in the opposite direction.

In the E-58H, E-78 & E-88 a pump check valve is used

to prevent hydraulic ﬂuid from leaking back through

the pump to the reservoir.

The E-58H, E-78 & E-88 unit uses one check valve

located between the “B” Solenoid Valve and the lift

cylinder. It prevents the hydraulic ﬂuid in the lift cylinder

from leaking back through the “B” Solenoid Valve

which could cause the plow to drift down.

DOUBLE ACTING PILOT CHECK VALVE

The pilot check valve is more sophisticated in that

it incorporates a piston in addition to the ball, seat

and spring. It is located between the “C” and “D”

Solenoid Valves on the E-88 and next to the “C”

valve on the E-58H & E-78. It has two functions: The

ﬁrst is to prevent the hydraulic ﬂuid in either power

angling cylinder from leaking back to the reservoir.

The second is to allow the hydraulic ﬂuid from the

retracting power angling cylinder during the angling

cycle to return to the reservoir. This is accomplished

by the pressurized hydraulic ﬂuid moving the piston

which forces the check ball off its seat. The E-88 also

uses an additional pilot check valve located next to

the “E” valve. This allows the “E” valve to control the

mount/dismount function.

CROSSOVER RELIEF VALVE

When plowing snow, a snow plow can be exposed

to damaging forces caused by impact with hidden

obstructions, ends of curbs, etc. With power angling,

these damaging forces can damage not only the snow

plow but also the vehicle. The crossover relief valve

has the function of protecting the snow plow system

against these damaging forces under normal snow

plowing conditions. The crossover relief valve, cannot

protect the system from damaging forces that are too

great due to abusive snow plowing conditions.

Basically, the crossover relief valve functions

exactly like the previously described pump relief

valve. It’s designed to open at a speciﬁc pressure.

In this instance, the pressure is not produced by

the pump but rather by the damaging force. As an

example, assume that the right corner of the plow

runs into the end of a curb. The impact will attempt to

collapse the right power angling cylinder. As a result,

very high hydraulic pressure is produced within the

cylinder. When the produced pressure is high enough,

it opens the crossover relief valve, allowing the highly

pressurized hydraulic ﬂuid to ﬂow directly to the left

power angling cylinder.

-18-

When the crossover relief valve functions in this

manner, the excessive pressure is released, the

excessive energy produced by the impact is absorbed,

and the result is only a change in angled position of

the plow.

The crossover relief valve is factory set to the speciﬁed

pressure of 3800 P.S.I. ± 400 this setting is non-

adjustable.

Содержание E-58H















































































Результаты поиска

Содержание E-58H

Отзывы:

Бренды по названию

Популярные бренды

Meyer E-58H, Руководство по обслуживанию

Результаты поиска

Содержание E-58H

Отзывы:

Бренды по названию

Популярные бренды