Metso NELES NDX 511 Series Скачать руководство пользователя страница 71

Страница: 71 / 88

GENER

INFO

SPECS

MOUNTING

T UP

OPER

ATION

AINTENANCE

DIMENSIONS

ORDER

LOGISTICS

NDX VALVE CONTROLLER

13.5.3.6 Counters

Fig. 71

Parameter name

Description

Total Operation

Time

Valve controller operation time, in hours.

Valve

Parameter name

Description

Travel Ratio

Valve Travel / Valve Reversals

Total Valve

Travel

This counter increases by 1 whenever he valve

has travelled one full stroke, or 100 % of valve

movement.

Total Valve

Reversals

This counter increases by 1 whenever the direction

of valve movement changes.

Control Ratio

Valve Reversals / Setpoint Reversals

Actuator

Parameter name

Description

Total Actuator

Travel

This counter increases by 1 whenever the valve

has travelled one full stroke, or 100 % of valve

movement.

Total Actuator

Reversals

This counter increases by 1 whenever the direction

of valve movement changes.

Setpoint

Parameter name

Description

Total Setpoint

Travel

This counter increases by 1 whenever the cumula

tive setpoint changes.

Total Setpoint

Reversals

This counter increases by 1 when the direction of

the setpoint changes.

HART Diagnostics

Parameter name

Description

Total

Messages In

Total HART messages received

Total

Messages Out

Total HART messages sent

HART Com

munication

Error Rate

during last

hour

HART communication error rate in percentage

during last hour

HART Com

munication

Error Rate

during last

day

HART communication error rate in percentage

during last day

13.5.3.7 Trends

Steady State Deviation Trend

Steady State Deviation is used to determine the basic

control accuracy of the valve. It is updated whenever the

setpoint is considered to have reached the desired position

as precisely as possible.

Steady State Deviation trend is stored in the device mem

ory. Trend shows the previous values of deviation during

24 hours, 30 full days, 12 full months, and 25 full years.

A change in the steady state deviation trend can be caused by:

•

The general performance of the valve and actuator

deteriorating.

•

higher friction of the valve trim

•

higher friction in actuator

•

actuator diaphragm or piston seal damage

•

change in process conditions

•

supply air problem

Steady State Deviation Trend high limit can be modified

by typing the value in the text box or by moving the limit

line in the trend graph.

Fig. 72

13 DEVICE TYPE MANAGER (DTM)

OPER

ATION

Содержание NELES NDX 511 Series

























































































Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды

Metso NELES NDX 511 Series, Инструкция по установке, обслуживанию и эксплуатации

Результаты поиска

Содержание NELES NDX 511 Series

Отзывы:

Похожие инструкции для NELES NDX 511 Series

Бренды по названию

Популярные бренды