manualshive.com logo in svg

Metso Full Bore Fire-Tite 9REL Series, Инструкция по установке, обслуживанию и эксплуатации

Поделиться
Скачать
Metso Full Bore Fire-Tite 9REL Series Скачать руководство пользователя страница 9

Plate or Bar

0.1875 Min. Typ.

3/8-16 Threaded Rod x 3" Long

ø5.375

(4) Cut-outs for Welding Purposes

1. Hold  o-ring in  place in  back  of

seat  with  compatible grease
during assembly.

2. Clamp seat  firmly  in body  or

insert seat cavity.

3. Tack weld 1/4" (6.35 mm) long in

(4)  places  90˚ apart  using 308L
weld rod. Do not exceed 300˚F at
weld.  Clean  weld areas to  bare
metal before welding.

ø5.375

3/8-16 Threaded Rod x 3” Long

0.1875 Min. Typ.

Plate or Bar

Figure 7  Barrier Seat Fixture & Instructions

1. 

Hold o-ring in place in back of 
seat with compatible grease 
during assembly.

2. 

Clamp seat firmly in body or 
insert seat cavity.

3. 

Tack weld 1/4”(6.35 mm) long 
in (4) places 90˚ apart using 
308L weld rod. Do not exceed 
300˚F at weld. Clean weld areas 
to bare metal before welding.

(4) Cut-outs for Welding Purposes

  

 

IMO 

4/19

  

IMO-R20 EN 

9

Содержание Full Bore Fire-Tite 9REL Series













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды