Metso 5300 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

Metso 5300 Скачать руководство пользователя страница 6

4.

SERVICE / SPARE PART

We recommend that valves be directed to our service

centers for maintenance. The service centers are equipped

to provide rapid turn-around at a reasonable cost and offer

new valve warranty with all reconditioned valves.

NOTE: When sending goods to the service center for

repair, do not disassemble them. Clean the valve carefully

and flush the valve internals. Include the material safety

datasheet(s) (MSDS) for all media flowing through the

valve. Valves sent to the service center without MSDS

datasheet(s) will not be accepted.

For further information on spare parts and service or

assistance visit our web-site at www.metso.com/valves.

NOTE: When ordering spare parts, always include the

following information:

a. Valve catalog code from identification plate,

b. If the valve is serialized – the serial number (from

identification plate)

c. From Figure 5, the ballooned part number, part

name and quantity required.

IMO 11/17

6

IMO-302 EN

«
...
4
5
6
7
8
...
»

Содержание 5300













Отзывы:

Нет отзывов