Metropolitan Industries, Inc. Sump Boss BP2000 Скачать руководство пользователя страница 15

Страница: 15 / 19

Sump Boss

Metropolitan Industries, Inc.

www.metropolitanind.com

OPERATION MANUAL

Dated: 9/17/09

Supersedes: None

Document No.: SBossO&M

Page 15 of 19

www.sumpro.com

1. The pump cord is not properly plugged into

the control unit.

2. The primary switch has failed.

3. The Smart Charger is damaged. This could

be caused by a jammed impeller, or motor

overheating.

4. The motor is damaged.

5. The brushes are worn out. This would most

likely occur in an older unit.

See Figure H

Screen Seven.

This means that the auxiliary

alarm/pump switch has activated. When this

occurs one of two things is happening:

1. The main pump switch has failed.

2. The water is coming into the basin faster than

the pump can pump it out. This scenario will

sound a continuous

beeping alarm. This

may also be caused by a depleted battery in

the DC mode. Turn on the pump and check

% of battery life left.

CONTINUOUS

BEEPING

WARNING! HIGH

WATER ALERT

This completes the operating scenarios of the

SUMP BOSS

system. As you can see, this

product was designed to be extremely user-friendly and should always warn and assist

you in resolving any problems that may occur during the life of this product.

Содержание Sump Boss BP2000




















Результаты поиска

Содержание Sump Boss BP2000

Отзывы:

Бренды по названию

Популярные бренды

Metropolitan Industries, Inc. Sump Boss BP2000, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Sump Boss BP2000

Отзывы:

Бренды по названию

Популярные бренды