background image

Disconnect the negative battery terminal to 
prevent an accidental short circuit.  Remove 
(2) screws below the ashtray.  Unclip the 
dash trim bezel.  Disconnect the cigarette 
lighter wiring and remove the bezel.  
Remove (2) bolts securing the rear of the 
factory head unit and disconnect the wiring.

ACURA Legend  1991-96

2

1

Disconnect the negative battery terminal to 
prevent an accidental short circuit.  Using a 
small screwdriver, unclip the perimeter of the 
radio trim bezel.  Disconnect the climate 
control and rear defroster wiring and remove 
the bezel.  Remove (4) Phillips screws 
securing the factory head unit/trim bezel 
assembly.  Loosen (2) Phillips screws 
securing the back of the head unit to the 
metal housing and slide the unit out.  (It is 
NOT necessary to remove the screws 
securing the metal housing to the bezel).  
Disconnect the wiring. 

ACURA TL  1996-98

2

1

Cut and remove the 

TOP

 clips from the 

Radio Housing.

  

5

6

Cut and remove the 

TOP

 clips from the 

Radio Housing.

  

ISO-DIN HEAD UNITS:

  Mount the 

Rear Support Bracket

 to the back of the pocket with 

(2) 

Phillips Screws

 supplied.

  

Skip to the Installation Instructions for ALL VEHICLES on Page 

#11.

ISO-DIN HEAD UNITS:

  Mount the 

Rear Support Bracket

 to the back of the pocket with 

(2) 

Phillips Screws

 supplied.

  

Skip to the Installation Instructions for ALL VEHICLES on Page 

#11.

3

3

Содержание 99-7892







Отзывы: