manualshive.com logo in svg

METHVEN Aroha 01-9106, Руководство по установке

Поделиться
Скачать
METHVEN Aroha 01-9106 Скачать руководство пользователя страница 21

Methven Australia Pty Ltd

ABN 15 104 813 390

Melbourne, Australia

www.methven.com

WMKA21005

IMPORTANT

Please read all of the instructions before installation

MA019441

      

Aroha Wall Top Assembly

01-9441 (Pair)

Use of this product is recommended for domestic and commercial applications.

All pipework must be thoroughly flushed prior to the installation of the mixer.

Inline filter washers must be installed on both hot and cold supplies to prevent foreign particles 

damaging the ceramic head works.

Do not remove the ceramic head works from the wall top assemblies when installing.

Methven recommends a licensed plumber carry out all installations in compliance with  

the requirements of AS/NZS 3500. This product complies with AS/NZS 3718 regulations.

JUNE 2012

Installation Guide

www.methven.com

Customer Care Hotline: 1300 METHVEN (638 483)

Email: [email protected]

Note: It is the responsibility of the installer to ensure a water proof seal is achieved between the 

faceplate and the finished surface of the wall. If in any doubt about the quality of the seal, the 

faceplate should be removed and then reinstalled using silicone to ensure a seal is achieved.

Installation

 

Ø 35mm

Ø 35mm

1.

2.

3.

5.

6.

Distance from mounting stud to 

front of wall lining: 

Std - 58-63mm

Ext - 63-75mm 

Hot

Col

d

Do not discard screws

For deeper 

installations, remove 

short threaded head 

works collars and 

replace with optional 

04-9646 Spindle 

Extension Kit (kit 

sufficient to extend 

two headworks)

(Available seperately)

 

4.

Содержание Aroha 01-9106























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды