manualshive.com logo in svg

METHVEN Aroha 01-9106, Руководство по установке

Поделиться
Скачать
METHVEN Aroha 01-9106 Скачать руководство пользователя страница 20

Methven Australia Pty Ltd

ABN 15 104 813 390

Melbourne, Australia

www.methven.com

WMKA21005

IMPORTANT

Please read all of the instructions before installation

MA019403

      

Aroha Hob Mounted Swivel Bath Spout

01-9403

Use of this product is recommended for domestic and commercial applications.

All pipework must be thoroughly flushed prior to the installation of the mixer.

Inline filter washers must be installed on both hot and cold supplies to prevent foreign particles 

damaging the ceramic head works.

Do not remove the ceramic head works from the mixer when installing.

Methven recommends a licensed plumber carry out all installations in compliance with  

the requirements of AS/NZS 3500. This product complies with AS/NZS 3718 regulations.

JUNE 2012

Installation Guide

Installation 

Maximum hole diameter through bench for 1/2" BSP tube is 22mm.

www.methven.com

Customer Care Hotline: 1300 METHVEN (638 483)

Email: [email protected]

Care and Cleaning

Never use abrasives to clean this product. Clean regularly with contamination free warm soapy water 

and a damp soft cloth. 

Operating Pressure:

Min 150kPa, Max 500kPa. 

Bath Spout

Washer

Locknut

1/2” BSP

Base Ring

Swivel Push Fit Connector

M5 Grub Screw

2.5mm Allen Key

Содержание Aroha 01-9106























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды