background image

User Manual

EM606

s a l e s @ m e t e r s . c o . u k    |    W h i t e  L u n d  I n d u s t r i a l  E s t a t e  L a n c a s t e r  L A 3  3 B T   |    0 1 5 2 4  5 5 5  9 2 9

TROUBLE SHOOTING

            

The power supply 
indicators are off.
(L1, L2 & L3 LED)

The register 
doesn’t count.

No pulse outputs.

The pulse output rate is
incorrect

Please contact technical support.

Are the fuses or/and surge protection 
defect?
  
Make sure the wires are connected properly 
and tighten the screws if possible.

Check if there is 230V AC voltage between N
and one of the L connections with a voltage
meter.

  
Check if there is 400V AC volt between N and
one of the L connections with a voltage meter.
If the checks above don’t solve the problem,
please contact technical support.

The meter is not connected to a
power source

L1, L2, L3 and N are not connected
correctly

There is no 230V AC between the N
and one of the L connections when
power is supplied to the meter.

There is no 400V AC between the L
connections   when   power   is
supplied to the meter.

There is almost no load connected to
the meter.

The pulse output is not supplied with 
DC power.

The pulse output is not connected 
correctly.

Still no response.

Check if the (P-: red or P+: green) consumption
led   is flashing. 40 flashes of the LED at 400
pulses per kWh equals 0.1kWh.
  

Check the external voltage source (Ui) is 5-27V
DC with a voltage meter

Check if the connection is correct:  the 5-27V DC
should be connected to the collector connection 
(pin 28+ or pin 30+) and the signal wire (S) to 
the emitter connection (pin 29- or 31-)
  
Please contact technical support.

The consumption LED
is not flashing.

The pulse cable is not connected.

The load on the line is very low.

Connect the pulse cable.

Check the Ohm meter readings

No data received by the
M-Bus communication
port.

The ID is not correct.

The communication distance 
is too long.

Too many meters connected.

The M-Bus terminals are not
connected correctly.

Check the Meter ID by looking for the A in the
display. The number in front of the A, for
example 15A gives the actual address the
meter uses. The default for this meter is 0A.

Make the distance between the meter and the
reading device shorter. Make sure it is no more
than ≤1000m 
    
The number of M bus devices connected to the
meter should not exceed 64.
    
Make sure that the M-bus wires are connected
to terminals 34and 35. If the checks above
don’t solve the problem, please contact
technical support for a meter replacement.

Содержание EM606 M-Bus












Отзывы: