Quick Installation Manual REV:202204
2G-2S.0.3.F-BOX-PoE
Industrial PoE+ Managed Switches
www.metel.eu 21/23
www.iplog.eu
P1 – P3: Fast ethernet ports 10 / 100Mbps. The production
firmware supports PoE according to IEEE 802.3af / at.
The maximum power consumption from one port is
30W. The maximum power of PoE over all ports is
90W. Performance on individual ports can be set in
the Simuland v4 application.
FE ports are protected by overvoltage protection 150A (8/20μs).
BUS1, BUS2:
2 serial buses
RS485.Overvoltage
protection 30A
(8/20μs).
4. Insert Optical Module
Any SFP module complying with MSA requirements
(agreement of SFP modules manufacturers) can be
inserted into the SFP slot. For modules with duplex
transmission over one fiber (wavelength multiplex) we
must ensure that the optical modules are connected
correctly to each other. That means that e.g. for WDM
modules METEL can interconnect W4 with W5. We
can’t interconnect W4 with W4 or W5 with W5.
Note:
For the correct functioning of LAN-RING.v1 and v2 it is
necessary to observe the correct connection to the GBIC
modules. W4 module must be plugged into the slot
MiniGBIC-G1 and module labeled W5 into the slot
labeled MiniGBIC-G2.
W5
Tx:1550nm
Rx:1310nm
W4
Tx:1310nm
Rx:1550nm
~
V1
+V2
~
V1/+V1
+V2
GND
5
4
3
2
1
Galvanically Separated Cover
Lightning Arrestors
FE 1 … FE 3
P
1
P
2
P
3
U
SB
IN
2
|
IN
1
O
U
T
G
2
R
IN
G
G
1
P
W
R
miniGBIC-G2 miniGBIC-G1
G
N
D
B
-
A
+
G
N
D
B
-
A
+
G
N
D
IN
2
IN
1
N
.O
.
C
O
M
N
.C
.
OUT
BUS1
BUS2
CLASS 1 LASER
PRODUCT!
www.metel.eu
2G-2S.0.3.F-BOX #1-988-220
B
2
|
B
1
LAN-RING Ethernet Switch
~
V
1
+
V
2
~
V
1
/+
V
1
+
V
2
G
N
D
5
4
3
2
1
USB:
local USB
management
See page 22 for
connection
information.
SFP SLOTS miniGBIC
100/1000BASE-X
Redundant DC Power Supply
Main Input +10 to +60V DC
Redundant Input +10 to +60V DC
Note: Terminals 2 and 4 are connected.
AC Power
Input 10 to 30V AC
1. Mounting
Install the switch on a level surface or DIN35. The
necessary holders are included.
2. Connect the Power
According to the pictures below, connect the power
supply in the range of 10-60VDC or 10-30VAC. Connection
of supply is indicated by LED PWR switching on.
See page 22 for important information regarding
the el. safety of the PoE power supply.
3. Grounding of Overvoltage Protections
Connect the protection with the green-yellow
wire, which is part of the switch, to an earth point
with a resistance of up to 10Ω.
The switch cover is galvanically separated from
the electronics on the PCB, which allows its use in
systems with a grounded (+) or (-) pole. A
lightning arrester is connected between the GND
terminal and the cover.
IN1, IN2
Programmable digital/alarm inputs for
connection of contact switches, tampers,
PIR sensors,...Inputs are protected with
overvoltage protection 30A (8/20μs).
OUT
Relay with change-over contact. Output
is protected with resetable current
protection.
5
4
3
2
1
+
+
GND
Source
+
GND
Source
5
4
3
2
1
5
4
3
2
1
~
~
GND
Source
