www.metel.eu 19/23
www.iplog.eu
MIB FILE NAME
DI
METEL-COMIO-DIO-MIB
Alarm
METEL-COMIO-EZS-MIB
OUT
METEL-COMIO-DIO-MIB
PoE
METEL-POE-PP-MIB
Displays the status of digital inputs. Switching DI / Alarm modes.
Display of alarm input statuses.
Status display / output relay control, pulse length setting, etc.
Status reading / PoE power control on ports.
Modbus
METEL-SERVICES-MODBUS-MIB
802.1X
METEL-SERVICES-DOT1X-MIB
HW
METEL-BOARD-MIB
Switch
METEL-SWITCH-MIB
Read / write / create modbus registers.
Read statuses / control settings related to 802.1X authentication.
Display of basic information about HW, temperature, power supply, USB status, enable traps ...
Reading statistics / Port control.
BUS
METEL-COMIO-BUS-MIB
Camera
METEL-SERV.-CAMDRIVER-MIB
RS485 bus settings.
Control of HTTP, CGI cameras, rotation via Onvif Profile S.
LAN-RING switches belong to the L2 industrial switches, which corresponds
to the supported network protocols. We recommend using L2 / 3 G series
switches in applications requiring Layer 3 protocol support.
10BaseT,
100BaseT(X) / 100Base FX, 1000Base(X) for IEEE 802.3, IEEE 802.3u , IEEE 802.3ab
LAN-RING switches on metal and optical ports are 100% compatible with LAN devices from other
manufacturers. In addition, all metal ports are equipped with surge protectors for better EMC.
PoE up to 95W / Port According to IEEE 802.3af, IEEE 802.3at, UPOE and POH Standards
The production firmware of LAN-RING switches supports a wide range of PoE standards.
PoE 90W According to IEEE 802.3bt Standard
In addition to the production firmware, fw with PoE support according to IEEE802.3bt is also available.
IGMP - Internet Group Management Protocol
The switches support the creation of multicast groups in IGMPv1 and V2 versions.
LLDP - Link Layer Discovery Protocol
Switches support the LLDP protocol to promote their identity and capabilities among neighboring devices
on the LAN. We use this protocol to draw the topology in the SIMULandv4 software.
SNMP - Simple Network Management Protocol
Switches are supported by a variety of monitoring and visualization softwares. For security reasons,
exclusively encrypted SNMP(.v3) and methods are used for communication with these softwares:
SNMP SET
- SNMP device settings. A typical example is relay setup and any configuration of fast / gigabit
Ethernet ports or RS485 serial buses.
SNMP GET
- finding status based on a query from the control system. As a rule, non-critical operational
information is transmitted in this form. The SNMP manager periodically queries SNMP agents. The
disadvantage is that the transmission of information can occur with a delay of several seconds.
SNMP TRAP
- the device autonomously sends status information to the control system. SNMP TRAP is
usually used for critical state transmission. Its advantage over SNMP GET is immediate response.
&
We recommend using ZABBIX software (tested) or any other software that supports SNMP.v3 / v2c
when monitoring METEL network devices.
For integration into other programs, MIB files are available at www.metel.eu, which, in addition to the
so-called public MIB files written in RFC documents, contain a number of PRIVATE MIB files for even
more detailed monitoring and control of the system. The table below shows their selection.
IEEE 802.1X - Port Access Control
LAN-RING switches make it possible to protect the network from access by unauthorized persons or
devices. In addition, all successful and especially unsuccessful attempts to authorize the switch can be
reported directly to the add-on software. Any attempt to penetrate the network is thus directly
transferred to the security of the building.
Radius Servers
Software
Authenticator
Supplicants
EAPOL
EAP
EAP
Radius
Authentication Failed / Passed
Network Protocols
