Metabo KHE 5-40, Оригинальное руководство пользователя, Страница: 10 / 68

ENGLISH en
10
- Insert the chisel.
- Push the sleeve (8) forwards and turn the chisel
until it is in the desired position.
- Push/ release the sleeve (8) backwards.
- Turn the chisel until it engages.
7.4 Switching on and off
Torque setting:
Press the trigger switch (12) to switch on the
machine.
To switch off release the trigger switch (12).
Continuous operation (only in chiselling
mode ):
The machine can be switched to continuous mode
(KHE...: only in chiselling mode ) by pressing the
button (10) .
To switch off, press the (10) button once again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
7.5 Setting impact force
Rotate the adjustment wheel (16) to change the
impact strength (and speed). The impact strength is
increased from setting 1 to 5 and the mode display
(14) flashes. In setting 6, the tool delivers the
maximum impact strength, in this setting the mode
display (14) is constantly lit.
Scope of application
wheel
Plaster/light construction materials ............................ 1-2
Brickwork/removing tiles............................................ 3-4
Drilling/chiselling into concrete .................................. 5-6
7.6 Metabo VibraTech (MVT)
For reduced vibrations and less stress on the
hands.
Always apply a moderate amount of pressure to the
handle when pushing down the machine and do not
force. Vibrations are reduced most effectively at the
central position (11).
The power tool should be cleaned regularly, often
and thoroughly through all air vents using a vacuum
cleaner or by blowing in dry air. Prior to this
operation, separate the power tool from the power
source and wear protective glasses and dust mask.
A damaged dust protection cap (6) must be
replaced immediately.
To replace the dust protection cap (6) slide the tool
lock (7) back. Grasp the dust protection cap and pull
firmly forwards and off. Fit the new dust protection
cap onto the spindle at an angle and press hard to
secure.
Overload:
The machine has shut down by itself. The
signal indicator (15) flashes. The machine was
overloaded (30%)! Let the machine cool down, only
then can you continue to work. Avoid further
overloading.
Restart protection:
The machine does not start. The signal
indicator (15) flashes . Restart protection is active.
If the mains plug is inserted with the machine
switched on or if the power supply is restored
following an interruption, the machine does not start
up. Switch the machine off and back on again.
Carbon brushes worn:
The signal indicator (15) flashes:
The carbon brushes are almost completely worn
(remaining operating time approx. 8 hours). If the
brushes are completely worn, the machine switches
off automatically. Have the brushes replaced by an
authorised service centre.
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
1
=Rated input power
P
2
=Power output
T =Torque
n
1
=No-load speed
D
1
=Max. drilling diameter in concrete with
impact masonry bits
D
2
=Max. drilling diameter in concrete with
impact core cutters
8. Cleaning, Maintenance
9. Troubleshooting
10. Accessories
11. Repairs
12. Environmental Protection
13. Technical Specifications