Metabo KGS 216 Plus, Оригинальная инструкция по эксплуатации

Страница: 37 / 80

ENGLISH
37
For special tasks the following accesso-
ries are available at your specialised
dealer – see back cover for illustrations:
Saw Blades for KGS 216 Plus
A TCT Saw Blade
216 × 2.4/1.8 × 30 24 ATB 5° neg.
For rip and cross cuts in solid wood.
B TCT Saw Blade
216 × 2.4/1.8 × 30 48 ATB 5° neg.
For rip and cross cuts in solid wood
and particle board.
C TCT Saw Blade
216 × 2.4/1.8 × 30 60 TF 5° neg.
For rip and cross cuts in coated or
veneered boards, panels, cable
ducts, NF extrusions and laminate.
Saw Blades for KGS 254 Plus and
KGS 254 I Plus
D TCT Saw Blade
254 × 2.4/1.8 × 30 24 ATB 5° neg.
For rip and cross cuts in solid wood.
E TCT Saw Blade
254 × 2.4/1.8 × 30 48 ATB 5° neg.
For rip and cross cuts in solid wood
and particle board.
F TCT Saw Blade
254 × 2.4/1.8 × 30 60 ATB 5° neg.
For rip and cross cuts in coated or
veneered boards.
G TCT Saw Blade
254 × 2.4/1.8 × 30 80 TF 5° neg.
For rip and cross cuts in coated or
veneered boards, panels, cable
ducts, NF extrusions and laminate.
Saw Blades for KGS 315 Plus
H TCT Saw Blade
315 × 2.4/1.8 × 30 48 ATB 5° neg.
For rip and cross cuts in solid wood
and particle board.
I TCT Saw Blade
315 × 2.4/1.8 × 30 84 ATB 5° neg.
For rip and cross cuts in coated or
veneered boards.
J TCT Saw Blade
315 × 2.4/1.8 × 30 96 TF 5° neg.
For rip and cross cuts in coated or
veneered boards, panels, cable
ducts, NF extrusions and laminate.
A
Danger!
Repairs to power tools may only be car-
ried out by qualified electricians!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. The address can be found in the
spare parts list.
Please attach a description of the fault
to the power tool.
The machine's packing can be 100%
recycled.
End-of-life power tools and accessories
contain large amounts of valuable raw
materials and plastics which must be
recycled.
This manual was printed on chlorine-
free bleached paper.
This section describes problems and
malfunctions which you should be able
to resolve yourself. If the measures de-
scribed here do not solve your problem,
see 'Repairs'.
A
Danger!
Many accidents happen particularly in
connection with problems and faults.
Therefore please note the following:

Always unplug before troubleshoot-
ing.

Check that all safety devices are
operational again after each fault
service.
Motor does not run
No mains voltage:

Check cables, plug, outlet and
mains fuse.
Motor overheated (KGS 254 I Plus):

Remove cause for overheating, let
cool down for a few minutes and
then start again.
No crosscut function
Transport lock activated:

Deactivate the transport lock.
Safety lock engaged:

Release safety lock.
Sawing performance too low
Saw blade blunt (possibly tempering
marks on blade body);
Saw blade not suitable for material be-
ing cut (see section 'Technical Data');
Saw blade warped:

Replace saw blade (see section
'Maintenance').
Saw vibrates heavily
Saw blade warped:

Replace saw blade (see section
'Maintenance').
Saw blade incorrectly mounted:

Remove the saw blade and then
mount it again correctly (see chap-
ter 'Care and Maintenance').
Saw squeaks during start-up
Drive belt tension too low:

Tighten the drive belt (see section
'Maintenance - Drive belt tensioning').
Rotary table stiff
Sawdust build-up under rotary table:

Remove saw dust.
10. Available Accessories
11. Repair
12. Protection of the Envi-
ronment
13. Troubleshooting