Messersi TC50 Скачать руководство пользователя страница 35

Страница: 35 / 37

7. TROUBLESHOOTING: CAUSES AND REMEDIES

PROBLEM

CAUSE

SOLUTION

The machine moves jerkily

There is no oil in the tank

Check the level and top up if
necessary

Air in the hydraulic
transmission system

Check that the piping and
connections are intact

Hydrost. syst. oil filter.
plugged

Replace filter cartridge

Lever operated too abruptly
and too fast

Operate the lever delicately

The machine does not use
all its power and does not
achieve maximum
performance

The hydraulic oil used differs
from the one indicated

Check and replace with
suitable oil if necessary

Hydrost. syst. oil filter.
plugged

Replace filter cartridge

The tracks tend to jump the
traction housing

The track has loosened with
use

Adjust following the
indications reported in the
paragraph on "CHECKS
AND CONTROLS" under
GENERAL MAINTENANCE

One of the two tracks is
blocked

Foreign bodies have worked
their way in between the track
and the frame

Remove the foreign body

Hydraulic motor failure

Contact an authorized
workshop

Pump damaged

Contact an authorized
workshop

Hydraulic piping failure

Check and replace if
necessary

The dump body hatch does
not open or close

Hook device damaged

Check lever, seat, etc. and
restore the original condition
if necessary

The engine does not start

Start-up starter or switch set
in the wrong position

Restore correct position as
indicated in the engine user's
manual

Fuel tank empty

Check and refuel if
necessary

Wrong fuel used

Check and, if necessary,
clean out the tank and
replace

The raised dump body does
not descend

Mechanical impediment

Remove the obstacle

Articulation pin blocked

Grease

Cylinder or gasket damaged

Check and replace if
necessary

The dump body does not
rise

Joint and or hydraulic pump
failure

Check and replace if
necessary

Содержание TC50






































Результаты поиска

Содержание TC50

Отзывы:

Похожие инструкции для TC50

Бренды по названию

Популярные бренды

Messersi TC50, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TC50

Отзывы:

Похожие инструкции для TC50

Бренды по названию

Популярные бренды