background image

CHANGING THE BATTERIES

Low Battery Warning

 : If the batteries are low the 

red

 

light will appear or the safe will 

not unlock

 after entering 

your code.

 Locate battery compartment [on the inside of door]

 Replace batteries with new 

4AA Alkaline Batteries

 Test lock before closing & locking your safe

 

 

NOTE : If the batteries die while the safe is locked, 

use the override keys. 

OPERATING YOUR SAFE

1

 Enter : 

Code - A 

& the 

green

 light will appear

2

 Pull handle before the 

green

 light disappears & open door

3

 To lock safe, close door & push handle back to the closed position

4

 Make sure your safe is locked & secure before walking away!

 

Valid Code

 

:

 The 

green

 light will appear for 

5 seconds

 

Invalid Code : 

Keypad will 

'beep'

 

6 times

 while the 

orange

 light appears

LOCK-OUT PENALTY

If an incorrect code is entered 

3 times consecutively

, a 

Lock-Out Penalty

 will 

be activated. During this lockout period, the keypad will not respond & the 

orange

 light will 

flash

 

every second

 until the lockout period is over. The 

lockout period will last for approximately 

3 minutes

.

PROGRAMMING YOUR SAFE

1

 Open the safe & locate the 

red

 

program button

 on the inside of the door

2

 Press the 

red program button

 & 

release; keypad will 

'beep'

 once & the 

orange

 light will appear for 

10-15 

seconds

3

 Before the 

orange

 light disappears - 

Enter : 

New Code - B

 

Valid Entry :

 keypad will 

'beep'

 

times

 Code can be 

3-8 digits

 

 If a mistake has been made, wait for 

the 

orange

 light to disappear & repeat steps 1-3

 

IMPORTANT : Test your New Code 3 or more times before closing door. 

Keep a record of your code.

MAWS-SERIES

 ELECTRONIC LOCK INSTRUCTIONS  

|

  

PG.4

Содержание MAWS Series













Отзывы: