manualshive.com logo in svg

Meritor RS-220, Руководство по обслуживанию

Поделиться
Скачать
Meritor RS-220 Скачать руководство пользователя страница 8

 

Section 2
Disassembly 

 

4

 

4.

Remove the tapered dowels and separate the 
axle shafts from the main axle hub assembly. 

 

Figures 2.3 and 2.4

 

. 

5.

Install a cover over the open end of each axle 
assembly hub where an axle shaft was 
removed.

 

Air Hammer Vibration Method 

CAUTION

 

Do not use a chisel or wedge to loosen the axle 
shaft and tapered dowels. Damage to the axle 
shaft, the gasket and seal, and the axle hub 
can result. 

 

1.

Use a round hammer bit and an air hammer 
such as Chicago Pneumatic CP-4181-Puler,
or equivalent, to loosen tapered dowels and 
axle shaft. 

2.

Place the round hammer bit against the axle 
shaft (flange) between the hub studs. Operate 
the air hammer at alternate locations between 
the studs to loosen the tapered dowels and 
axle shaft from the hub. 

 

Figure 2.5

 

.

3.

Mark to identify each axle shaft before it is 
removed from the axle assembly. 

4.

Remove the tapered dowels and separate the 
axle shaft from the main axle hub assembly. 

 

Figure 2.4

 

.

 

Figure 2.3

Figure 2.4

STUD

NUT

WASHER

TAPERED
DOWEL

GASKET

STUD

CAPSCREW

WASHER

AXLE

SHAFT

(FLANGE)

SHAFT

HUB AXLE

 

Figure 2.5

ROUND HAMMER BIT

BETWEEN HUB STUDS

Содержание RS-220






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды