manualshive.com logo in svg

Meritor RS-220, Руководство по обслуживанию

Поделиться
Скачать
Meritor RS-220 Скачать руководство пользователя страница 33

Section 5

Assembly

29

Select Drive Pinion Bearing Cage 
Adjustment Shims

This adjustment helps to position the drive pinion 
in relation to the ring gear for the purpose of 
ensuring the ideal position of tooth contact.

The desired distance is obtained by the installation 
of a shim packet below the drive pinion bearing 
case. 

Figure 5.14

.

There are shim packs of different thicknesses 
available for this adjustment. Refer to 

Table G

.

The pack should always consist of at least three 
pieces, and the thicker pieces should be placed on 
the outside to ensure maximum sealing capability.

Table G 

Determine the Shim Packs

Using a Caliper

1.

Write down the nominal mounting dimension 
(ND) for the drive pinion. This dimension is the 
nominal distance taken from the center of the 
ring gear to the rear drive pinion bearing cone 
face. 

Figure 5.15

. Refer to 

Table H

.

Table H 

2.

Identify and write down the drive pinion 
variation (PV).

All drive pinions have an individual variation 
with respect to their ND. This variation, 
expressed in hundredths of a millimeter, and 
a + or – sign is stamped on the pinion’s head. 

Figure 5.16

.

Figure 5.14

Model

Radius

Thickness 
Inches (mm)

240

028 455-6

0.010 (0.25)

028 454-8

0.005 (0.13)

028 453-0

0.003 (0.08)

220/224

027 288-4

0.005 (0.13)

230

027 289-2

0.010 (0.25)

027 290-6

0.003 (0.08)

SHIM PACK

ADJUSTMENT

OF THE 

DRIVE PINION

BEARING CAGE

Figure 5.15

Model

ND

240

219.08

230

206.38

220/224

200.00

Figure 5.16

Содержание RS-220






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды