background image

Section 3
Installing Replacement Parts 

MM-34
Page 20

Revised 11-02

Purge Valve Assembly

1.

Review 

Figure 3.11

 to make sure you have all 

of the parts required to replace the purge valve.

Use the grease included with the replacement 
kit to lubricate O-rings and seals. 

Do not 

grease the rubber seat.

If shims are included in the replacement kit, 
they must be installed above and below the 
spring. If they are not included, they are not 
needed.

2.

Remove the snap ring, valve head and spring.

3.

Remove the piston assembly from the base. 

Figure 3.12

.

4.

Remove washer and O-rings from the base.

5.

Clean and inspect the valve bore. If the bore is 
damaged so that a tight seal cannot be 
maintained, replace the air dryer.

6.

Apply a thin layer of grease to the valve bore 
and to all O-rings (use the grease included 
with replacement kit).

7.

Install new washer and O-ring in dryer base 
and on valve head.

8.

Assemble piston assembly:

O

Install O-ring in groove on piston head.

O

Install piston seat in groove on piston base.

O

Install washer on piston.

NOTE:  

Lip on washer must face piston seat. 

Figure 3.13

.

9.

Install washer on piston assembly. 

Figure 3.14

.

Figure 3.11

Figure 3.12

1002173b

METAL

SHIMS

(IF REQUIRED)

1002174a

SPRING

VALVE HEAD

PISTON

ASSEMBLY

Figure 3.13

Figure 3.14

1002175b

LIP

1002176a

Содержание System Saver 1000













































Отзывы: