Meridian Bulk Seed Tender Seed Express 225RST Скачать руководство пользователя страница 51

Страница: 51 / 68

13. TROUBLESHOOTING

13.1 TROUBLESHOOTING CHART

PROBLEM

CAUSE

SOLUTION

Engine will not start.

No fuel.

Fill the fuel tank.

Low engine oil.

Fill the crankcase with oil.

Cold engine.

Open choke.

Ignition key switch off.

Turn ignition key switch on.

Battery dead.

Recharge or replace battery.

Engine problem.

Refer to engine manual.

Auger will not start.

Not rotating.

Start engine and increase speed above
1400 RPM.

Drive pulley connection or auger
coupling.

Repair or replace.

Drive belt slipping.

Increase belt tension.

No hydraulic oil in reduction case.

Check oil level.

Failed centrifugal clutch.

Replace clutch.

Electrical functions are not work-
ing properly.

Battery cable or battery.

Check battery cable and make sure battery
is fully charged.

Improper ground.

Check for proper grounding of electrical
circuit.

Remote throttle doesn’t work.

No input power.

Check charge of battery. Recharge or
replace, as required.

Check connections in the remote throttle
harness. Be sure connectors are clean and

terminalsarefirmlypushedtogether.

Содержание Bulk Seed Tender Seed Express 225RST





































































Результаты поиска

Содержание Bulk Seed Tender Seed Express 225RST

Отзывы:

Похожие инструкции для Bulk Seed Tender Seed Express 225RST

Бренды по названию

Популярные бренды

Meridian Bulk Seed Tender Seed Express 225RST, Руководство оператора

Результаты поиска

Содержание Bulk Seed Tender Seed Express 225RST

Отзывы:

Похожие инструкции для Bulk Seed Tender Seed Express 225RST

Бренды по названию

Популярные бренды