Meridian Bulk Seed Tender Seed Express 225RST Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 68

background image

42

11.4 ENGINE ACTUATOR REPLACE-
MENT

11.4.1 Actuator Removal

WARNING

CRUSHING HAZARD
Ensure the seed tender is blocked to
prevent movement.

Ensure the engine is not running and
remove the key during the following
procedures. Serious injury or death
can result from being caught in moving

parts.

1. Remove bolt (1) that secures cover (2) to

actuator mounting bracket (3). Remove the
cover.

2. Disconnect the actuator cable from the engine

harness at connector (4).

3. Remove four bolts (5), washers (6), lock nuts

(7), and spacers (8).

4. Remove washer nut (9) and then disconnect

spring (10) from actuator arm (11).

11.4.2 Actuator Installation

1. Connect the cable of the new actuator to

engine harness connector (4).

2. Position actuator arm (11) so it is pointing

away from the end where the cable is attached
to the unit, as shown. Use actuator switch
(12) on the delivery tube to position the arm.

Note:

Do not move the arm manually or the unit

will be damaged.

«
...
40
41
42
43
44
...
»

Содержание Bulk Seed Tender Seed Express 225RST





































































Отзывы:

Нет отзывов

Похожие инструкции для Bulk Seed Tender Seed Express 225RST

Brillion Turfmaker III Series

Бренд: Landoll Страницы: 104

Бренд: LELY Страницы: 24

drive 4X IC D EX

Бренд: EWM Страницы: 107

Бренд: Nexus Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды