background image

Mercury Security Corporation, 

©

 2008

      BR20       Doc. 10107-0024  rev. 1.03  10/2008

  

                            

   Page 2

Information subject to change without notice.

The reader is rated to operate over an extended
temperature range and the electronics are conformal
coated against moisture.  If the reader is expected to
be exposed to weather, use the dielectric grease to
coat the field connections.  After field connection/
configuration is made, the grease is to be applied on
the DIP switch slides, keypad connection, and the
RJ-11 jack to seal out moisture.

Do not use sealant to seal reader case to the
wall

. Doing so will trap water in the reader and may

cause damage to the reader.

6. TTL Interface:

The TTL interface has the standard 5-wire interface widely used in the access control application. In addition, an input
to control the buzzer is provided. Cable with minimum of 24AWG wires should be used.

Pin #

Wire

Signal

Description

  1

Red

Vin

Power supply input, 5Vdc or 12Vdc, Model dependent

  2

Green

/Data (Mag) or

Reader data output

/Data 0 (Wieg)

  3

White

/Clock (Mag) or

Reader data output

/Data 1 (Wieg)

  4

Brown LED

LED input
1-wire control: 0V turns on the green LED

         5V turns on the red LED

2-wire control: 0V turns on the red LED

  5

Orange Buzzer/LED

Buzzer/LED input
1-wire control: 0V turns on the buzzer
2-wire control: 0V turns on the green LED

  6

Black

Signal Ground

Power supply return, DC ground

7. Grounding the Reader:

To avoid  having ESD (electrostatic discharge) interfering with the operation of the reader, the reader casing shall be
grounded. This can be accomplished by tying the mounting bracket to earth ground locally (e.g. grounded conduit).

8. DIP Switch Setting:

The DIP switch on the BR20 reader is used to select a preset format, the functions for the LED and buzzer, and the
output signal format, etc. The preset format determines how the card is interpreted. Refer to the format specification
for detail. The settings are for STANDARD models ONLY.  The BR20 does not support the tamper switch option.

MODULAR PLUG

1 (RED) +5 or +12Vdc

2 (GRN) DATA 0/DATA

3 (WHT) DATA 1/CLOCK

4 (BRN) LED

5 (ORG) BUZZER/LED

6 (BLK) GND

depends on model

FORMAT

SW -4

SW -3

SW -2

SW -1

OUTPUT

LED

BUZZER

TAMPER

0

ON

ON

ON

ON

DATA 1/DATA 0 1-W IRE LED

YES

NO

1

ON

ON

ON

OFF

CLOCK/DATA

1-W IRE LED

YES

NO

2

ON

ON

OFF

ON

CLOCK/DATA

1-W IRE LED

YES

YES

3

ON

ON

OFF

OFF

CLOCK/DATA

1-W IRE LED

YES

NO

4

ON

OFF

ON

ON

DATA 1/DATA 0 1-W IRE LED

YES

NO

5

ON

OFF

ON

OFF

DATA 1/DATA 0 1-W IRE LED

YES

NO

6

ON

OFF

OFF

ON

DATA 1/DATA 0 1-W IRE LED

YES

NO

7

ON

OFF

OFF

OFF

DATA 1/DATA 0 1-W IRE LED

YES

NO

12

OFF

OFF

ON

ON

CLOCK/DATA

2-W IRE LED

NO

NO

13

OFF

OFF

ON

OFF

DATA 1/DATA 0 2-W IRE LED

NO

NO

15

OFF

OFF

OFF

OFF

CLOCK/DATA

1-W IRE LED

YES

YES

Содержание BR20







Отзывы: