Mercury 200 Sport-Jet Скачать руководство пользователя

Страница: 79 / 84

TROUBLESHOOTING

Engine Runs Erratically

POSSIBLE CAUSES

• Spark plugs fouled or defective. Refer to

Maintenance

section.

• Incorrect setup and adjustments.
• Fuel is being restricted to the engine.

a. Engine fuel filter is obstructed. Refer to

Maintenance

section.

b. Fuel tank filter obstructed.
c. Stuck antisiphon valve on built‑in fuel tank.
d. Fuel line is kinked or pinched.
e. Injector plugged.

• Threaded connection of an air hose is loose.
• Fuel pump failure.
• Ignition system component failure.

Performance Loss at Normal RPM

POSSIBLE CAUSES

• Boat overloaded or load improperly distributed.
• Excessive water in bilge.
• Boat bottom is dirty or damaged.

Performance Loss at Wide‑Open Throttle

LOW RPM (USUALLY ENGINE RELATED)

• Throttle not fully open.
• Exhaust system blocked.
• Ignition system problem.
• Fouled spark plug or failed injector.
• Air compressor inlet blockage.

HIGH RPM (USUALLY PUMP RELATED)

• Damaged impeller.
• Worn impeller or worn wear ring.

Содержание 200 Sport-Jet





















































































Результаты поиска

Содержание 200 Sport-Jet

Отзывы:

Похожие инструкции для 200 Sport-Jet

Бренды по названию

Популярные бренды

Mercury 200 Sport-Jet, Руководство пользователя

Результаты поиска

Содержание 200 Sport-Jet

Отзывы:

Похожие инструкции для 200 Sport-Jet

Бренды по названию

Популярные бренды