Mercury 10 FOURSTROKE Скачать руководство пользователя страница 55

Страница: 55 / 134

IMPORTANT: Do not try to fill the oil level to the top of the operating range

(upper hole). Oil level is correct as long as it appears in the operating range

between the upper and lower hole.

a -

Oil level operating range

b -

Dipstick

c -

Oil fill cap

5. If the oil level is below the operating range (lower hole), remove the oil fill

cap and add approximately 200 ml (7 oz.) of specified outboard motor oil.

Allow a few minutes for the added oil to drain to the oil sump and check

the dipstick. Repeat the process until oil level is in the operating range

between the upper and lower holes. Do not try to fill to the upper end of

the operation range (upper hole).

NOTE: Under certain conditions, the operating temperature of 4‑stroke

outboard engines may not get hot enough to evaporate the normal fuel and

moisture that accumulate in the crankcase. These conditions include operating

at idle for long periods, repeated short trips, slow speed or quick stop‑and‑go

operation, and operating in cooler climates. This additional fuel and moisture

that collects in the crankcase eventually ends up in the oil sump and will add

to the total volume of oil that appears on the dipstick reading. This increase in

oil volume is known as oil dilution. Outboard engines can typically handle large

amounts of oil dilution without causing durability problems. However, to ensure

extended life of the outboard engine, Mercury recommends that the oil and

filter be changed regularly following the oil change interval and using the

recommended oil quality. It is further recommended that if your outboard is

operated frequently in the conditions described above, that more frequent oil

change intervals be considered.

6. Push the dipstick back in all the way.
7. Install the oil fill cap hand‑tight.
8. Install top cowl.

31988

FUEL AND OIL

eng

Содержание 10 FOURSTROKE







































































































































Результаты поиска

Содержание 10 FOURSTROKE

Отзывы:

Похожие инструкции для 10 FOURSTROKE

Бренды по названию

Популярные бренды

Mercury 10 FOURSTROKE, Инструкция по установке, эксплуатации, обслуживанию и гарантии

Результаты поиска

Содержание 10 FOURSTROKE

Отзывы:

Похожие инструкции для 10 FOURSTROKE

Бренды по названию

Популярные бренды