background image

Mercury Security 

©

 2013   

SR10k    Doc. 10107-0007   

Rev 1.08  

  Page 

2

          

Table of Contents

Section Page

Overview 3

Quick Start and Confi guration Planning 

5

Programming Guide 

6

Operating Mode Specifi cations 

10

Mode 1: Basic Access Control with Door Monitoring 

10

Mode 2: Restricted Access Control with Door Monitoring 

11

Mode 3: Access Control and Alarm Panel Control 

12

Mode 4: Restricted Access and Alarm Panel Control 

13

Mode 5: "Supervisor" Controlled Restricted Access 

14

Mode 6: "Two Door" Access Control 

14

Mode 7: Access Control with "Door Bell" Feature 

15

Mode 8: Dual Output Toggle on Valid Access 

15

Installation 16

Maintenance 17

Specifi cations 

17

Dimensions and Typical Confi guration Diagrams 

18

  Mercury 

Security 

 

         2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755

 

 

 

     (562) 986-9105, FAX (562) 986-9205

                            www.mercury-security.com

This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device 
may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that 
may cause undesired operation.

Содержание SR10k




















Отзывы: