Mercury Racing HP1200 SCi Dry Sump Скачать руководство пользователя страница 94

Страница: 94 / 106

COLD WEATHER OR EXTENDED STORAGE

3. Open the fuel shut off valve located between the tank and the

water separating fuel filter.

4. Turn the key switch to "RUN" and wait three seconds to allow

the fuel pump to prime the system.

5. Start the engine.
6. If the engine does not stay running, repeat the starting

procedure until the engine starts and runs smoothly.

7. Check the oil pressure gauge immediately after the engine

starts. If the oil pressure is not within the specified range, see

Specifications,

stop the engine immediately, and determine

cause.

8. Do not advance the throttle until the engine idles and runs

smoothly and the water temperature reaches a minimum of 54

°C (130 °F).

9. Observe instrumentation to ensure that all systems are

functioning properly.

10.After the engine has warmed up, check the water temperature

gauge to ensure that the engine temperature is not abnormally

high. If it is, stop the engine immediately and determine cause.

11.Inspect the engine for fuel, oil, fluid, water and exhaust leaks.
12.Check the steering system and shift and throttle control for

proper operation.

PRIMING THE FUEL SYSTEM PRIOR TO STARTING

WARNING

Avoid fire or explosion. Gasoline is extremely flammable and

highly explosive. Ensure key switch is "OFF." Do not smoke or

allow a spark or open flame in area when removing or installing

fuel components. Wipe up any spilled fuel immediately.

1. Perform all

Before Starting

steps.

2. Close the fuel shut off valve located between the fuel tank and

the water separating fuel filter.

3. Attach an outboard type portable fuel tank with primer bulb to

the water separating fuel filter inlet fitting with a hose clamp.

4. Squeeze the primer bulb until the bulb becomes firm.

Содержание HP1200 SCi Dry Sump











































































































Результаты поиска

Содержание HP1200 SCi Dry Sump

Отзывы:

Похожие инструкции для HP1200 SCi Dry Sump

Бренды по названию

Популярные бренды

Mercury Racing HP1200 SCi Dry Sump, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP1200 SCi Dry Sump

Отзывы:

Похожие инструкции для HP1200 SCi Dry Sump

Бренды по названию

Популярные бренды