Mercury Racing HP1200 SCi Dry Sump Скачать руководство пользователя страница 99

Страница: 99 / 106

TROUBLESHOOTING

Engine Runs Rough, Hard to Start, Misses, and/or

Backfires

Possible Cause

Remedy

Faulty ignition system component.

Service ignition system.

Clogged fuel filter.

Replace filters.

Stale or contaminated fuel.

If contaminated, drain tank. Fill with

fresh fuel.

Kinked or clogged fuel line or fuel tank

vent line.

Replace kinked lines or blow out

lines with compressed air to remove

obstruction.

Flame arrestor plugged.

Clean or replace the flame arrestor.

Rev limiter engaging at

wide‑open‑throttle.

Change to propeller with more pitch.

Manifold Air Pressure (MAP) sensor

failure.

Test MAP sensor and replace if

faulty.

Poor Performance

Possible Cause

Remedy

Throttle not fully open.

Inspect throttle cable and linkages for

proper operation.

Damaged or wrong propeller.

Replace propeller.

Excessive bilge water.

Drain and check for cause of entry.

Boat overloaded or load improperly

distributed.

Reduce load or redistribute load more

evenly.

Boat bottom fouled or damaged.

Clean or repair as necessary.

Flame arrestor dirty.

Change or clean flame arrestor.

Supercharger not creating boost.

Check supercharger belt, determine

cause for low boost.

Manifold Air Pressure (MAP) sensor

failure.

Test MAP sensor and replace if faulty.

Содержание HP1200 SCi Dry Sump











































































































Результаты поиска

Содержание HP1200 SCi Dry Sump

Отзывы:

Похожие инструкции для HP1200 SCi Dry Sump

Бренды по названию

Популярные бренды

Mercury Racing HP1200 SCi Dry Sump, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP1200 SCi Dry Sump

Отзывы:

Похожие инструкции для HP1200 SCi Dry Sump

Бренды по названию

Популярные бренды