background image

Industry Canada Statement 

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, 

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject 

to the following two conditions: 

1.  This device may not cause interference. 

2.  This device must accept any interference, including interference that may cause undesired 

operation of the device. 

 

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux 

CNR d’Innovation, Sciences et Développement économique Canada applicables aux 

appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions 

suivantes : 

1.  L’appareil ne doit pas produire de brouillage; 

2.  L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 

susceptible d’en compromettre le fonctionnement. 

 

This radio transmitter [IC: 6961A-600100010] has been approved by Innovation, Science and 

Economic Development Canada to operate with the antenna types listed below, with the 

maximum permissible gain indicated. Antenna types not included in this list that have a gain 

greater than the maximum gain indicated for any type listed are strictly prohibited for use with 

this device. 

Group 

Ant. No. 

Brand 

Model Name 

Antenna Type 

Connector 

1 20 

1 Meraki 

MA-ANT-20 

Omni 

N-Type 

2 Meraki 

MA-ANT-20 

Omni 

N-Type 

3 Meraki 

MA-ANT-20 

Omni 

N-Type 

4 Meraki 

MA-ANT-20 

Omni 

N-Type 

2 21+23 

1 Meraki 

MA-ANT-23 

Sector 

N-Type 

2 Meraki 

MA-ANT-23 

Sector 

N-Type 

3 Meraki 

MA-ANT-21 

Sector 

N-Type 

4 Meraki 

MA-ANT-21 

Sector 

N-Type 

3 25 

1 Meraki 

MA-ANT-25 

Sector 

N-Type 

2 Meraki 

MA-ANT-25 

Sector 

N-Type 

3 Meraki 

MA-ANT-25 

Sector 

N-Type 

4 Meraki 

MA-ANT-25 

Sector 

N-Type 

4 27 

1 Meraki 

MA-ANT-27 

Sector 

N-Type 

2 Meraki 

MA-ANT-27 

Sector 

N-Type 

3 Meraki 

MA-ANT-27 

Sector 

N-Type 

4 Meraki 

MA-ANT-27 

Sector 

N-Type 

- - 

5 Meraki 

MR76 

PIFA 

I-PEX 

- - 

6 Meraki 

MR76 

PIFA 

I-PEX 

 

Содержание MR76-HW































Отзывы: