Memsic AHRS380ZA-200 Скачать руководство пользователя страница 5

Страница: 5 / 113

DMU380ZA Series

User’s Manual

Doc# 7430-3810 Rev. 02

Page iii

7.2.9

Error Response ............................................................................................54

Output Packets (Polled) ......................................................................................54

7.3

7.3.1

Identification Data Packet ...........................................................................54

7.3.2

Version Data Packet ....................................................................................54

7.3.3

Test 0 (Detailed BIT and Status) Packet ......................................................55

Output Packets (Polled or Continuous) ...............................................................55

7.4

7.4.1

Scaled Sensor Data Packet 0 .......................................................................55

7.4.2

Scaled Sensor Data Packet 1 (Default IMU Data) .......................................56

7.4.3

Angle Data Packet 1 (Default AHRS Data) ................................................57

7.4.4

Angle Data Packet 2 (Default VG Data) .....................................................58

7.4.5

Nav Data Packet 0 .......................................................................................59

7.4.6

Nav Data Packet 1 (Default INS Data) ........................................................60

DMU380ZA Advanced UART Port Commands .......................................................62

Configuration Fields ...........................................................................................62

8.1

Continuous Packet Type Field ............................................................................62

8.2

Digital Filter Settings ..........................................................................................63

8.3

Orientation Field .................................................................................................63

8.4

User Behavior Switches ......................................................................................65

8.5

Hard and Soft Iron Values ..................................................................................65

8.6

Heading Track Offset ..........................................................................................65

8.7

Commands to Program Configuration ................................................................67

8.8

8.8.1

Write Fields Command ................................................................................67

8.8.2

Set Fields Command ....................................................................................68

Read Fields Command ........................................................................................69

8.9

Read Fields Response .....................................................................................69

8.10

Get Fields Command .......................................................................................69

8.11

Get Fields Response ........................................................................................70

8.12

DMU380ZA Advanced UART Port BIT ...................................................................71

Built In Test (BIT) and Status Fields ..................................................................71

9.1

Master BIT and Status (BITstatus) Field ............................................................73

9.2

hardwareBIT Field ..............................................................................................74

9.3

hardwarePowerBIT Field ....................................................................................74

9.4

hardwareEnvironmentalBIT Field ......................................................................74

9.5

comBIT Field ......................................................................................................74

9.6

comSerialABIT Field ..........................................................................................75

9.7

comSerialBBIT Field ..........................................................................................75

9.8

Содержание AHRS380ZA-200


















































































































Результаты поиска

Содержание AHRS380ZA-200

Отзывы:

Бренды по названию

Популярные бренды

Memsic AHRS380ZA-200, Руководство пользователя

Результаты поиска

Содержание AHRS380ZA-200

Отзывы:

Бренды по названию

Популярные бренды