Meinberg IMS LANTIME M500 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 132

background image

12 Attachment: Technical Information

12.6.20 REL1000: Error Relay Module

The REL1000 error relay module can be switched by various operating states (e.g.: Clock Not Sync). If the
internal hardware clock is running synchronous to the source, the relay is switched to NO (Normaly Open)
mode. In case of an error, the relay switches to NC (Normaly Closed) mode.

Depending on the hardware configuration of the IMS system, i.e. redundant with RSC module and two inte-
grated reference clocks or with SPT module and only one reference clock, different relay states can be switched.

In redundant operation, the two clocks and the changeover unit are monitored as standard (CLK1 - relay
A, CLK2 - relay B, RSC - relay C). This jumper setting is supplied per default in redundant systems.

Possible configurations of Error Output:

Relay A:

Clock 1 / Notification Events

→

Relays

Relay B:

Clock 2 / PPS

Relay C:

RSC / 10 MHz / Notification Events

→

Relay

In redundant mode, the jumpers on the REL1000 are set as shown below:

IMS - LANTIME M500

Date: 19th March 2020

111

«
...
115
116
117
118
119
...
»

Содержание IMS LANTIME M500





































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMS LANTIME M500

Бренд: Unisys Страницы: 20

Бренд: Xerox Страницы: 2

BladeCenter HS23

Бренд: IBM Страницы: 30

System x3950 X6

Бренд: IBM Страницы: 53

ML-2010 - B/W Laser Printer

Бренд: Samsung Страницы: 25

Бренд: EMC Страницы: 34

SuperServer 6029U-TR25M

Бренд: Supermicro Страницы: 151

Ultra Enterprise 3000

Бренд: Sun Microsystems Страницы: 48

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Бренд: LaCie Страницы: 74

PRIMERGY PG-RSBOP2

Бренд: Fujitsu Страницы: 68

SPARC Enterprise T5440 Server

Бренд: Fujitsu Страницы: 92

SPARC Enterprise T5140

Бренд: Fujitsu Страницы: 138

SPARC Enterprise T5440 Server

Бренд: Fujitsu Страницы: 214

SPARC Enterprise T5140

Бренд: Fujitsu Страницы: 130

Бренд: Fujitsu Страницы: 514

Бренд: Hitachi Страницы: 58

Бренд: Hitachi Страницы: 192

TS-73AeU Series

Бренд: QNAP Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды