Meinberg IMS LANTIME M500 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 132

background image

2.10 Return of Electrical and Electronic Equipment

ATTENTION!

WEEE Directive on Waste Electrical and Electronic Equipment 2012/19 / EU

(WEEE Waste Electrical and Electronic Equipment)

Separate Collection
Product Category: According to the device types listed in the WEEE Directive, Appendix 1,
this product is classified as an IT and communication device.

This product meets the labeling requirements of the WEEE Directive. The product symbol on
the left indicates that this electronic product must not be disposed of in domestic waste.

Return and Collection Systems
For returning your old equipment, please use the country-specific return and collection systems
available to you or contact Meinberg.

The withdrawal may be refused in the case of waste equipment which presents a risk to
human health or safety due to contamination during use.

Return of used Batteries
Batteries marked with one of the following symbols may not be disposed of together with the
household waste according to the EU Directive.

12

Date: 19th March 2020

IMS - LANTIME M500

«
...
16
17
18
19
20
...
»

Содержание IMS LANTIME M500





































































































































Отзывы:

Нет отзывов

Похожие инструкции для IMS LANTIME M500

Univerge SV8100

Бренд: NEC Страницы: 2

ML-2010 - B/W Laser Printer

Бренд: Samsung Страницы: 25

APSolute Vision

Бренд: Radware Страницы: 81

Бренд: Omega Страницы: 49

Бренд: Iwatsu Страницы: 338

Бренд: Valcom Страницы: 4

Бренд: IBM Страницы: 100

Бренд: TYAN Страницы: 81

Connectware PortServer TS 8/16

Бренд: Digi Страницы: 106

Бренд: NAIM Страницы: 20

Бренд: Alcatel-Lucent Страницы: 4

Бренд: XtendLan Страницы: 28

Smartstor NS4600

Бренд: Promise Technology Страницы: 370

Бренд: Solid Страницы: 102

Бренд: Supermicro Страницы: 78

Бренд: Supermicro Страницы: 72

Бренд: Supermicro Страницы: 78

Бренд: R/Evolution Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды