manualshive.com logo in svg

Meinberg GPS167TGP, Руководство по эксплуатации

Поделиться
Скачать
Meinberg GPS167TGP Скачать руководство пользователя страница 9

9

GPS167 Features

The hardware of GPS167 is a 100mm x 160mm microprocessor board. The 105mm
wide front panel integrates a 4 x 16 character LC display, two LED indicators and 4
push buttons. The receiver is connected to the antenna/converter unit by a 50 ohm
coaxial cable (refer to "Mounting the Antenna"). Feeding the antenna/converter oc-
curs DC insulated via the antenna cable. Optional an antenna splitter for up to four
receivers connected to one antenna is available.

GPS167 is using the "Standard Positioning Service" SPS. The navigation message

coming in from the satellites is decoded by GPS167´s microprocessor in order to track
the GPS system time. Compensation of the RF signal´s propagation delay is done by
automatical determination of the receiver´s position on the globe. A correction value
computed from the satellites´ navigation messages increases the accuracy of the
board´s oven controlled master oscillator (OCXO)

 

and automatically compensates the

OCXO´s aging. The last recent value is restored from the battery buffered memory at
power-up.

The GPS167 provides different optional outputs, i.e. three progammable pulse

outputs, modulated/unmodulated timecode output, and up to a total of four RS232
COM ports. Additionally, you can order the GPS167 with different OCXOs (e.g.
OCXO-LQ / MQ / HQ or an external Rubidium) to match the required accuracy.

The hard- and software configuration of the clock is dis-

played if the NEXT key is pressed two times from the root

menu.

Содержание GPS167TGP































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды