manualshive.com logo in svg

Meinberg GPS167TGP, Руководство по эксплуатации

Поделиться
Скачать
Meinberg GPS167TGP Скачать руководство пользователя страница 19

19

NEXT Key

When editing parameters (LCD cursor is visible) this key moves the cursor to the next
digit rsp. to the next parameter to be edited. If the current menu just displays data
(cursor not visible) pressing this key switches to a submenu (if available).

INC Key

When editing parameters this key increments the digit or letter at the cursor position.

The Menus in Detail

Root Menu

The root menu is shown when the receiver has completed initialization after power-
up. The first line of the display shows the receiver´s mode of operation as described
above. The text "NORMAL OPERATION" might be replaced by "COLD BOOT",
"WARM BOOT", "UPDATE ALMANAC". If the antenna is disconnected or not
working properly, the text "ANTENNA FAULTY" is displayed instead.

The next two lines display the current date, the name of the time zone (as defined in
the setup menu) and local time. The last line shows the state of the synthesizer. It
might look like following:

"Synth disabled"

Synthesizer is disabled (frequency setted on 0.000)

"F.synth inhibited"

GPS167 is not synchronized jet, but the synthesizer will be en-
abled after synchronisation.

"..............(free)"

The frequency is generated, but the phase is not synchronous
to the pulse output P_SEC, either because the synthesizer is
enabled although GPS167 has not synchronosized jet or be
cause the frequency is setted to more than 10kHz.

"..............(drft)"

The frequency is generated and the phase was already syn-
chronous to the pulse output P_SEC, but in the moment the
phase can´t be controlled or adjusted because no satellite is
received now.

Содержание GPS167TGP































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды