manualshive.com logo in svg

Meinberg GPS167TGP, Руководство по эксплуатации

Поделиться
Скачать
Meinberg GPS167TGP Скачать руководство пользователя страница 18

18

The Front Panel Layout

FAIL LED

The FAIL LED is turned on whenever the
TIME_SYN output is low (receiver is not syn-
chronized).

LOCK LED

The LOCK LED is turned on when after power-
up the receiver has acquired at least four satelli-
tes and has computed its position. In normal
operation the receiver position is updated conti-
nuously as long as at least four satellites can be
received.

LC Display

The 4 x 16 character LC display is used to show the receiver´s status and let the user
edit parameters. The keys described below let the user select the desired menu. The
next chapter lists all available menus in detail. A quick reference of the available
menus and submenus can be found at the end of this document.

MENU Key

This key lets the user step through several display menus showing specific data.

CLR/ACK Key

This key has to be used when parameters are to be modified. When this key is pressed
the parameters that have been edited are saved in the battery buffered memory. If the
menu is left without pressing CLR/ACK all changes are discarded.

NEXT

INC

CLR

ACK

MENU

FAIL

LOCK

Содержание GPS167TGP































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды