Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 46

Meinberg GPS164-LQ/PPFO-3/REL-1/DAHS Скачать руководство пользователя страница 7

Page 3

2 Safety Hints

WARNING!

This device is powered by a dangerous voltage. Nonobservance of the safety instructions of
this manual may lead to serious damage to persons and property and to danger to life!
Installtion, commissioning, maintenance and operation of this device are to be carried out by
qualified personnel only.

The general safety instructions and standards ( e.g. IEC, DIN, VDE, EN ) for installation and
work with high voltage equipment as well as the respective national standards and laws must
be observed.

NONOBSERVANCE MAY LEAD TO SERIOUS DAMAGE TO PERSONS AND PROPERTY AND TO
DANGER TO LIFE!

The device may not be opened. Repair services may only be carried out by the manufaturer.

Supply lines for this decice must be equipped via an appropriate switch that must be mounted
close to the device and must be marked as a mains switch for the device.

To ensure safe operation supply mains connected to this decice must be equipped with a fuse
and a fault-current circuit breaker according to the applicable national standards for safe
operation. The devide must be connected to a protective earth with low grounding resistance
according to the applicable national rules.

WARNING!

DANGER TO LIFE BY ELECTRICAL SHOCK!

NO LIVE WORKING!

Wiring or any other work done the connectors particularly when connectors are opened may
never be carried out when the installation is energized.

All connectors must be covered to prevent from accidental contact to life parts.

ADVICE

:

ALWAYS ENSURE A PROPER INSTALLATION!

Additional safety information for installation devices

•

This device was developed and tested in accordance with the requirements dened in IEC61010-1 overvoltage

category II.

•

The device is intended for installation in an appropriate cubicle.

•

When the device is installed and operated in an end user device ( e.g a cubicle ), additional requirements

dened in IEC61010-1 must be fullled. Particularly the general standards for electrical safety (IEC, VDE,

DIN, ANSI e.g.) as well as the applicable national standards must be observed.

•

Protection against re must be ensured.

•

The device was developed and tested for industrial environments with a pollution grade 2 according to IEC

61010. Environments with a higher degree of pollution require additional measures such as installation in a

control box with air condition for example.

•

The device was designed and tested for a maximum ambient temperature of 50

◦

C.

•

Proper ventilation must be ensured, the device must not be covered.

GPS164

Date: 27th January 2016

3

«
...
5
6
7
8
9
...
»

Содержание GPS164-LQ/PPFO-3/REL-1/DAHS















































Отзывы:

Нет отзывов